Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
This mode can be used to provide more power to the subwoofer while maintaining stereo left and right. In this system, the 400 BDG Bridging Module accepts the stereo inputs and turns one channel over 180 degrees (inverts the channel). Both channel outputs of the amplifier are now connected to the subwoofer with the inverted channel being used as the negative input. This works because the two channels are 180 degrees out-of-phase. The left mid/high speaker is connected normally, but the connections to the right mid/high speaker must be turned over to retain the stereo effect. This means that the yellow lead now becomes the negative lead and the black/ yellow lead becomes the positive lead. A REMINDER: The speakers must never be grounded to the car chassis or body. To do so will cause severe noise problems and, in the case of bridging, cancel out the two-phase operation. -15V- LEFT- M5V RIGHT '■AUDIO GROUND DIN CONNECTOR All ORION Accessories and Amplifiers have this DIN configuration. 'Phantom Power’ (+15V & -15V) is supplied to all ORION accessory modules by the amplifier through the DIN cable. (When ORION amplifiers are not used, the ORION PPS 100 Phantom Power Supply is required.) Figure 10. Mixed Mono Connections in a Single Stereo Amplifier System Using a 400 BDG Bridging Module 16 DECK Luft Output This application is used when you want to maintain the stereo effect while doubling the output power of your amplifiers. The right amplifiers uro connected to the RIGHT output of the 400 BDG Bridging Module and the left amplifiers are connected to the LEFT output. In this system, the 400 BDG Bridging Module accepts the stereo inputs and turns one channel over 180 degrees (inverts the channel). Both channel outputs of each amplifier are now connected to the speaker with the inverted channel being used as the negative input. This works because the two channels are 180 degrees out-of-phase. The ORANGE lead from each amplifier is used as the positive lead and the YELLOW lead is used as the negative lead. The BLACK/YELLOW and BLACK/ORANGE leads are not used. A REMINDER: The speakers must never be grounded to the car chassis or body. To do so will cause severe noise problems and, in the case of bridging, cancel out the two-phase operation. -15V -LEFT- •v AUDIO GROUND DIN CONNECTOR All ORION Accessories and Amplifiers have this DIN configuration. "Phantom Power ( + 15V & -15V) is supplied to all ORION accessory modules by the amplifier through the DIN cable. (When ORION amplifiers are not used, the ORION PPS 100 Phantom Power Supply is required.) Figure 11. Method of Doubling Output of Amplifiers Using Bridged Stereo Right and Left 17 DECK + 15V vAUDIO GROUND "Phantom Power (+15V & -15V) is supplied to all ORION accessory modules by the amplifier through the DIN cable. (When ORION amplifiers are no* used, the ORION PPS 100 Phantom Power Supply is required.) ORION 30DBLP LOW PASS FILTER FILTERED LOWS AMPLIFIER SUBWOOFERS jf ORION 600 EQM EQUALIZER or ORION 500 PMQ PARAMETRIC EQUALIZER Vo 1 1 nVA/ ^ Yeiiuwv'/ yj Black/Yel low (-) |jjj , DIN Cable f = OR 1 ON “0HCCA Orange (+) Black/Orange (-) NONFILTERED LOWS AMPLIFIER / ORION 200 CRX CROSSOVER MODULE Low Freq "Output Yel low (+) Black/Yel low ( DIN Cable RION WOHCCA High Freq Output This diagram shows a typical application for an ORION 30 dBLP Low Pass Filter used to control the low frequencies applied to a pair of subwoofers. A 200 CRX Active Crossover is used to select the full range of the mid and high range frequencies, and to select the full range of lows applied to the unfiltered lows amplifier. Overall frequency control is provided by an ORION 600 EQM Equalizer ora 500 PMQ Parametric Equalizer. The RCA and DIN connectors at the INPUT to the 200 CRX Active Crossover are connected in parallel so that the RCA connectors can be used to connect the output of the equalizer directly to the Low Pass Filter so that the crossover module has no effect on the Low Pass Filter. This is an ideal application when you are using mismatched subwoofers or are experiencing speaker box resonance problems. A REMINDER: The speakers must never be grounded to car chassis or body. To do to will cause severe noise problems. DIN Cable Orange (+) Black/Orange ( HIGH/MID AMPLIFIER HIGH/MID SPEAKERS Yellow(+) Black/Yel low (-) ORION “0HCCA Orange (+) Black/Orange (-) Figure 12. Typical Use of an ORION 30 dBLP Low Pass Filter to Set Upper Limits of Low Frequencies DECK ORION 600 EQM EQUALIZER or ORION 500 PMQ PARAMETRIC EQUALIZER RCA/DIN Cable ORION 30 DBHP HIGH PASS FILTER ORION 30 DBHP 30 dB Pft Oct*** Hi|h Ptsi Croiiontr TWEETER AMPLIFIER Yel I ow (+) TWEETERS Front DIN Cable ■a . ORION 225H Black/Yellow (-) Orange (+) Rear MIDRANGE AMPLIFIER Black/Orange(-) Yel low (+) MIDRANGE SPEAKERS Front Black/Yellow(-) ORION 200 CRX CROSSOVER MODULE Low Freq Output DIN Cable DIN Cable 'S’.A, ...
Este manual também é adequado para os modelos :Avtousiliteli - 425HCCA (2.55 mb)