Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins. Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen. Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your vehicle which may be located behind the mounting surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely. wiring tips When making electrical connections to your amplifier, please observe the following: Use at least 8 gauge wire for power and ground connections. Wire the amplifier directly to the car battery. For the ground connection, use the shortest possible wire to a good chassis ground point. Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna. fusesAbout power fuses: Pyle Marine Series amplifiers feature built-in fuse systems. These fuses protect both the amplifier and the electrical system in your vehicle from fault conditions. If you ever need to replace the fuse in your Pyle Marine Series amp, use a fuse of exactly the same type and rating. A different type or rating of fuse may result in damage or fire. 10 troubleshooting No output. Confirm that all terminal strip connections are secure and tight. Check both in-line and built-in fuses. Both the +12V and the Remote terminals must have +12v referenced to chassis ground. protection Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal. To check if the amp is supplying signal, unplug the cables from the signal source (but leave them plugged into the amp). Briefly tap the center pin of each of the disconnected RCA plugs with your finger. This should produce a noise (feedback) in your speakers. The built-in protection circuitry in the Marine amplifiers will disable the amplifier if it senses an circuitry Only one channel works. input overload, a speaker short circuit, or extreme Confirm that all terminal strip connections are secure and tight. temperature conditions. Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint. When the protection circuit is activated by any of If you are using the Low Level RCA input, reverse the input plugs at the amplifier (i.e., switch the L with the R). Ifthese conditions, the Protection LED will be the channels which is silent switches to the other side, the problem is either in the head unit/other source or theilluminated. connecting cables. If this occurs, carefully inspect the system to Weak output. determine the source of the problem. Readjust the Input Level Control(s) to better suit the input signal. • If the shutdown was a result of a thermal overload Noise in the audio. condition, allow the amplifier to cool down before If the noise is a “whine” whose pitch follows the engine speed, confirm that the amplifier and any other signal sources (head unit, etc.) are properly grounded. attempting to restart it. If the noise is a “clicking” or “popping” noise whose rate follows the engine speed, this usually means that the • If the shutdown was a result of an input overload, vehicle is equipped with resistor spark plugs and wires, or that the ignition is in need of service. or speaker short circuit, be sure to correct the Check the rounting of the speaker and input wires to make sure they are not adjacent to wires which interconnect condition before restarting. lights and other accessories. The amplifier can be restarted by turning the remote If the above steps fail to improve or clear noise interference, the system should be checked by a professional mobilepower OFF and then ON again. audio installer. precautions Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident. Do not mount this amplifier so that the wire connections are unprotected, or in a pinched condition, or likely to be damaged by nearby objects. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, do so only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage that isn’t covered in the manufacturer’s warranty. 12 notes STOP YES! NO! 2-c hannel Amplifier (Operating in Stereo) 4 ohm 4 ohm Two 4-ohm speakers, wired in stereo, will present a 4-ohm load to each channel of the amplifier. Most two- channel amplifiers will work well in this configuration. Two 4-ohm speakers, wired in paralle...
Este manual também é adequado para os modelos :Avtousiliteli - PLMRA620 (105.52 kb)