For countries using 100V, 110V, 115V and 120V AC mains, select the 115V switch position on the Voltage Selector switch. For countries using 220V, 230V, and 240V AC mains, select the 230V switch position on the Voltage Selector switch. There is no externally accessible AC mains (line) fuse. The internal fuse is integral to the SMPS power supply and is not user serviceable. This fuse will not fail except under very unlikely fault conditions to the SMPS, and if this occurs a qualified service techn

Соедините напрямую с кузовом (корпусом) автомобиля при помощи кабеля сечением до 8 Ga. Для наилучшего соединения используйте кольцевую клемму. 2. Клемма (Remote Turn.on Terminal) Клемма предназначена для включения/выключения усилителя путём подачи на эту клемму управляющего напряжения +12В. Обычно этот сигнал появляется на выходе включенного головного устройства, имеющего функцию управления активной антенной или другим оборудованием. 3. Клемма “+” (B+ Terminal) Клемма предназначена для пода

This is useful for connection of component speakers or coaxials to this channel pair in a bi-amplified system. “x10” (High-Pass): Configures the filter to attenuate frequencies below a frequency TEN TIMES HIGHER than the indicated filter frequency at a rate of 12dB per octave. This is useful for connection of tweeters to this channel pair in a tri-amplified system. Channel 3 & 4 Filter: 12dB/octave High-Pass or Bandpass Filter “Off”: Defeats the filter completely, allowing the full range of freq

To connect the remote turn-on wire to the amplifier, strip 1/2-inch (12 mm) of insulation from the wire and insert it into the “Remote” receptacle on the power connector. Tighten the connector down using a Phillips screwdriver. inPut seCtions The J2-360.2’s has one pair of stereo inputs.The input section input section offers two input connection methods, one for high-level (speaker level) signals and one for low-level (preamp level) signals. 1) Low-Level Inputs: A standard left/ right pair of RC

A. AMPLIFIER MODEL : PA-305 INTRODUCTION Thank you for purchasing PYRAMID the MODEL PA-305 P. A. AMPLIFIER. The unit has been designed using the latest electronic technology available. The unit will offer exceptional performance and reliability at an affordable price. The unit dilivers 100 watts of power and features 4 microphone input jacks, 70-volt line output, CD/AUX input jacks, selectable speaker impedance (4Q, 8Q, 16Q , 70V) output, five individnal source mixing controls, master volume

26210086 Input frequency range MHz 90-862 Input level range dB.V 48-78 Output frequency range MHz 5-65 Max. output level dB.V 113-118 Power consumption W 3.5 Transmission protocol DOCSIS/EuroDOCSIS 2.0 Suitable for VGO 939, VGO 939-1G, VGF 939, VGF 939-1G, VOS 952/953, VOS 952-1G, VOS 953-1G, ORA 9022, ORA 9022-1G, ORA 920/921, VGP 9033 as of version A03 (Nov. 2008), VGP 9033-1G, VGP 9041 as of version A02 (Nov. 2008), VGF 9030/9040 16 HTE 10 - Hand-held unit With the HTE 10 hand-held unit one i

Couple the RCA input with the car stereo or equalizer outputs using RCA type connector cables. 5. POWER FUSE Power fuse protects both this amplifier and the automobile electrical system from wrong electrical conditions. 6.POWR SUPPLY TERMINAL Connect the +12V DC power supply into the terminal by lugs and screws accessible at the panel of this amplifier. A.BATT +12V Connect +12V DC power supply wire into the terminal from the terminal of the battery. B.GROUND Ground terminal connect the g

Enables the matching of input levels to the output levels from head unit (or other signal source). The input sensitivity of adjustment ranges from 6V to 200mV. crossover frequency control When crossover mode selector is in HIGHPASS mode, this control sets the lower frequency limit for audio program sent to the speakers. When crossover mode selector is in LOWPASS mode, this control sets the upper frequency limit for audio program sent to the speakers. bass boost level selector bass boost level co

Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines) Page 2 of 16 SA-430-17 Installation and Operating Instructions TABLE OF CONTENTS TABLE OF CONTENTS.............................................................................................................2 SPECIFICATIONS ......................