Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
9/26/06) General Safety Information DESCRIPTION The Sta-Rite Sink Pump System, Model Number DP233110V-01, is ideal for home wastewater removal from beautician or utility sinks and wet bars, and for drain water transfer from air conditioners or dehumidifiers. 1/3 HP submersible pump unit is equipped with a 3-prong grounding-type power cord. Motor is oil-filled (dielectric oil) and sealed for cooler running. Upper sleeve/lower ballbearing on motor shaft never need lubrication. Automatic reset thermal protection. SPECIFICATIONS Power supply required ...................................115V, 60 Hz. Liquid temp. range..........................................32° to 130°F Individual branch circuit required (minimum)......15 Amps Discharge...........................................................1-1.2" NPT UNPACKING AND INSPECTION Handle with care. Check items received against packing list to be sure that all equipment has been received. Inspect for shipping damage. If found, file claim with carrier immediately. GENERAL SAFETY INFORMATION Electrically powered sump pumps normally give many years of trouble-free service when correctly installed, maintained, and used. However, unusual circumstances (interruption of power to the pump, dirt/debris in the sump, flooding that exceeds the pump’s capacity, electrical or mechanical failure in the pump, etc.) may prevent the pump from functioning normally. To prevent possible water damage due to flooding, consult your dealer about installing a high water alarm. See the “Troubleshooting Chart” in this manual for information about common sump pump problems and remedies. For more information, see your dealer or call customer service. 1. Know the pump application, limitations, and potential hazards. 2. Disconnect power before servicing. 3. Release all pressure within system before servicing any component. PERFORMANCE 4. Drain all water from system before servicing. 5. Secure discharge line before starting pump. An unsecured discharge line will whip, possibly causing personal injury and/or property damage. 6. Check hoses for weak or worn condition before each use, making certain that all connections are secure. 7. Periodically inspect system components. Keep free of debris and foreign objects. Perform routine maintenance as required. 8. Provide means of pressure relief for pumps whose discharge line can be shut-off or obstructed. 9. Personal Safety: a. Wear safety glasses at all times when working with pumps. b. Keep work area clean, uncluttered and properly lighted – replace all unused tools and equipment. c. Keep visitors at a safe distance from work area. d. Make workshop child-proof – with padlocks, master switches, and by removing starter keys. 10. When wiring an electrically driven pump, follow all electrical and safety codes that apply. 11. This equipment is only for use on 115 volt (single phase) and is equipped with an approved 3-conductor cord and 3-prong, grounding-type plug. To reduce risk of electric shock, pull plug before servicing. This pump has not been investigated for use in swimming pool areas. Pump is supplied with a grounding conductor and grounding-type attachment plug. Be sure it is connected only to a properly grounded grounding-type receptacle. Where a 2-prong wall receptacle is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in accordance with codes and ordinances that apply. 12. All wiring should be performed by a qualified electrician. 13. Make certain power source conforms to requirements of your equipment. Model HP GPM of Water @ Total Feet of Head Shutoff5’ 10’ 15’ 20’ DP233110V-01 1/3 48.0 40.0 29.0 15.0 24’ SPECIFICATIONS HP Motor Full Load Amps Switch Setting Height Top Width Bottom Width Weight On Off 1/3 9.8 7" 2" 13-3/4" 15-1/8" 12" 32 lbs. General Safety / Assembly 3 14. Protect electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking cord. Replace or repair damaged or worn cords immediately. 15. Do not touch an operating motor. Modern motors are designed to operate at high temperatures. Risk of electric shock. If your basement has water or moisture on the floor, do not walk on wet area until all power has been turned off. If shut-off box is in basement, call electric company or hydro authority to shut-off service to house, or call your local fire department for instructions. Remove and replace system. Failure to follow this warning can result in fatal electrical shock. Risk of electric shock. Do not handle pump or pump motor with wet hands or when standing on wet or damp surface, or in water. Always disconnect the pump and switch from the electrical power source before doing any maintenance. 16. Pump water only with this pump. ASSEMBLY Steps 1 and 2 (See Figure 1) Step 3 (See Figure 2) Step 4 (See Figure 3) Install the discharge pipe hand-tight plus one-half turn. Step 5 (See Figure 4) Place the pump in the basin as shown. Align the discharge with one of the threaded ports in...