Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
A Ground Fault Current Interrupter (GFCI) must be installed to protect your electric outlet and prevent any possible electric shock. The unit must be supplied through a Ground Fault Current Interrupter outlet. The connection to the branch circuit should be consistent with the local and national wiring rules (electrical code). If the supply cord is damaged, it must be replaced by the manufacturer’s service agent or a qualified and trained person in order to avoid hazards. Always remember to turn the Power Supply OFF and unplug it from the power outlet before removing the cleaner from the pool. Shut off and unplug the Power Supply every time you remove the cleaner from the water. Do not plug the Power Supply in within 12 feet of the pool. Do not leave the cleaner in the pool all the time. Mishandling the unit can result in leakage of lubricants. Please keep the plug away from contact with water. iRobot Verro Owner’s Manual Cautions Please read this manual completely before operating your pool cleaner. Retain the safety and operating instructions for future reference. Do not switch the pool cleaner ON if it is not fully immersed in water. Operating the cleaner out of water will cause severe damage immediately and will result in loss of warranty. Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its cleaning cycle. This will allow the motors to cool adequately. Do not use Verro in a pool warmer than 100 degrees Fahrenheit. Do not use the floating power cord to lift Verro from the pool. Use the handle. Do not force the floating power cord plug. It will fit into the socket only one way. Do not leave your cleaner in direct sunlight when not in use. Never leave the Power Supply in direct sunlight and avoid leaving it in the rain. Tips Tip Clean the filter bag regularly. Verro uses the force of the water pumped through its filter bag to move properly. If the filter bag is not kept clean, Verro will not move or clean properly. Tip Store Verro in a dry place out of direct sunlight at a temperature between 50 and 104 degrees Fahrenheit. The Power Supply is water resistant, but not waterproof and may be damaged by rain. Important: Failure to properly store Verro will result in loss of warranty. Tip iRobot recommends using the mesh filter bag (included) when the pool contains a significant quantity of large debris (leaves, etc.), such as when the pool is opened for the season. The fine filter bag is ideal for filtering small debris (algae, sand, etc.) and for regular maintenance. Tip Periodically straighten the floating power cord with the Detangler. Tip Verro’s Power Supply has an automatic timer that shuts Verro OFF after approximately two hours of operation. When this happens, the power switch will remain ON. To start another cleaning cycle, switch the Power Supply OFF and then back ON and then press the reset button. iRobot Verro Owner’s Manual Table of Contents Anatomy ..................................................................... 6 - 7 Parts List.................................................................... 6 - 7 Using Verro................................................................. 8 How Verro Works......................................................... 11 Adjusting the Time Control Dial..................................... 12 Cleaning the Filter Bag................................................. 13 - 14 Maintenance and Adjustment....................................... 15 - 20 Troubleshooting........................................................... 21 - 23 Customer Care............................................................ 24 Anatomy Parts List 1. Cable Grommet 2. Body Assembly 3. Jet Tube Bushing 4. Jet Tube 5. Filter Screen 6. Pump Motor 7. Axle 8. 6” Wheel 9. Washer 10. Steering Axle Housing 11. Square Foam Float 12. Filter Bag 13. Foam Float Clip 14. Bottom Lid Assembly 15. Jet Valve Port 16. Jet Valve Housing 17. Floating Power Cord 18. Fixed Axle Housing 19. 2” Wheel 20. Side Plate 21. Handle 22. Wheel Hubcap 23. Star Washer 24. Jet Nozzle 25. Locking Tab iRobot Verro Owner’s Manual Jet Valve Housing Assembly 16 15A 15 15. Jet Valve Port 15A. Jet Valve Port Screw 16. Jet Valve Housing Time Control Dial Rear View Front View 1. Fuse Holder 2. Power Supply cord 3. Power (ON/OFF) Switch 4. Time Control Dial 5. Socket (For Floating Power Cord) 6. Reset Button Using Verro 1 Uncoil the floating power cord and spread it over the surface of the water, ensuring that it is not tangled or kinked. Place Verro upside down in the pool and rock it from side to side to allow air to escape. Turn Verro over and allow it to sink to the bottom of the pool so that the wheels rest on the bottom of the pool. Place the Power Supply in a dry area at least 3.5 meters/12 feet from the pool. 3.5m/12ft Plug the floating power cord into the Power Supply. Be sure not to force the plug as it will only go in one way. Ensure that the Po...