Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
It will fit into the socket only one way. The floating power cord must be locked in the socket on the Power Supply. Do not leave your cleaner in direct sunlight when not in use. Never leave the Power Supply in direct sunlight and avoid leaving it in the rain. Tips Tip Clean the filter bag regularly. Verro uses the force of the water pumped through its filter bag to maintain traction, particularly on the walls of the pool. If the filter bag is not kept clean, Verro will not clean properly and will not be able to climb the walls of the pool. Tip Change the direction of the handle before each cleaning run to prevent the floating power cord from becoming twisted and to improve coverage of the entire pool. (p. 8) Tip Store Verro in a dry place out of direct sunlight at a temperature between 50 and 104 degrees Fahrenheit. The Power Supply is water resistant, but not waterproof and may be damaged by rain. Important: Failure to properly store Verro will result in loss of warranty. Tip iRobot recommends using the mesh filter bag (available separately at when the pool contains a significant quantity of large debris (leaves, etc.), such as when the pool is opened for the season. The fine filter bag is ideal for filtering small debris (algae, sand, etc.) and for regular maintenance. Tip Periodically straighten the floating power cord with the Detangler. iRobot Verro Owner’s Manual Table of Contents Anatomy ..................................................................... 6 Parts List.................................................................... 7 Using Verro................................................................. 8 - 10 How Verro Works......................................................... 11 Cleaning the Filter Bag................................................. 12 - 13 Maintenance and Adjustment....................................... 14 - 18 Troubleshooting........................................................... 19 - 20 Customer Care............................................................ 21 Anatomy 1154235769231312111810814 iRobot Verro Owner’s Manual 22 22 1617 19 20 21 24 Parts List 1. Outlet Top 2. Pump Motor 3. Drive Motor 4. Handle Lock Mechanism 5. Pulley Assembly 6. Drive Belt 7. Drive Track 8. Body Assembly 9. Filter Screen 10. Side Plate 11. PVA Brush 12. Filter Bag 13. Bottom Lid Assembly 14. Handle Assembly 15. Cable Assembly 16. Power Supply (Transformer) 17. Transformer Socket 1. 8 Wheel Tube Assembly 19. OFF button 20. Light 21. ON button 22. Power Cord (Outlet) 23. Vacuum Intake Flaps 24. Lock Tabs Using Verro 1 Position the handle diagonally across Verro. Each time Verro cleans the pool, reverse the direction of the handle. This will help keep Verro from twisting the floating power cord and ensure more even coverage. Uncoil the floating power cord and spread it over the surface of the water. Place Verro in the water and rock it from side to side to allow air to escape. Let Verro settle to the bottom of the pool. Ensure that it is right side up and level. 3.5m/12ft Place the Power Supply (transformer) at least 3.5 meters /12 feet from the pool. iRobot Verro Owner’s Manual Using Verro (cont...) Plug the floating power cord in the Power Supply. Be sure not to force the plug as it will only go in one way. Once the plug is fully seated, turn the locking collar clockwise to lock it. Push and rotate clockwise Ensure the Power Supply at least 12 feet from the pool and plug it into a GFCI outlet. Ensure the electric outlet has been properly grounded. Never leave the Power Supply plugged in when Verro is not in use. warning: a Ground Fault Current Interrupter (GFCI) must be installed to protect your electric outlet and prevent any possible electric shock. Press the green Power button to start Verro; the light on the Power Supply will illuminate and Verro will start. The length of the cleaning cycle will vary based on pool size. To stop Verro before the end of the cleaning cycle, press the red Power button on the Power Suppy. Light Floating Power Cord Socket On Off lIGHT: Light indicates that robot is ON. On: Green button turns robot ON. OFF: Red button turns robot OFF. Using Verro (cont...) 10 11 When Verro has finished cleaning the pool it will stop automatically and the Power Supply light will go OFF. Wait 20 minutes before removing Verro from the pool to allow the motors to cool. Shut off and unplug the Power Supply every time you remove the cleaner from the water. Always remember to turn the Power Supply OFF and unplug it from the power outlet before removing the cleaner from the pool. Unplug the Power Supply from the GFCI outlet. Never leave the Power Supply plugged in when Verro is not in use. Unplug the floating power cord from the Power Supply (turn the locking collar on the plug counter-clockwise to unlock it). Rotate counter-clockwise and pull to unlock 1 Use the floating power cord to pull Verro ...