Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Owners Operating Instructions Part 3: Warranty Date of Installation: // // Model No. Serial No. Installed by: Purchased from: This Installation and Operating Instructions Manual is provided with the necessary information for the proper installation, operation and maintenance of your Raypak Heater. Please review and follow these procedures carefully. Keep this manual in a safe and accessible place for easy reference in the future. 3 PART 1 - FOR YOUR SAFETY For your safety do not operate this appliance before reading this instruction booklet. WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information consult your Raypak distributor, qualified installer, or service agency. WHAT TO DO IF YOU SMELL GAS? DO NOT try to light any gas appliance DO NOT touch any electrical switch. Turn off the gas supply at the gas meter Immediately, call your gas supplier or licensed gasfitter. NOTE: Some gases are heavier than air and it may be necessary to check for gas leaks at floor level. CAUTION DO NOT Operate this appliance before reading this instruction booklet. DO NOT Place articles on or against appliance. DO NOT Store chemicals or flammable materials in the same room as this appliance. DO NOT Store chemicals or flammable materials, on, or spray aerosols near this appliance. DO NOT Operate with panels, covers or guards removed from appliance. DO NOT Enclose this appliance (applies to external models only). DANGER Water temperatures above 45 Degrees Celsius can cause severe burns. Children, disabled and elderly persons are at the highest risk of being scalded. Feel water before bathing or showering and supervise where necessary. Keep this manual in a safe and accessible place for easy reference in the future. This Installation and Operating Instructions Manual is provided with the necessary information for the proper installation, operation and maintenance of your Raypak Heater. Please review and follow these procedures carefully. Model No. ..................... Serial No. .................... Installation Date .................. Part No. 209130.5: Effective 08/01/2001 (Replaces: 01/10/2000) 4 PART 1 - FOR YOUR SAFETY CAUTION! Ceramic Firetile Refractory is used in Raypak Heaters Possible risks of irreversible effects Harmful by inhalation May be irritating to the skin, eyes and respiratory system. WHEN HANDLING • Minimise airborne dust. • Wear an approved mask or respirator. • Avoid any contact with the skin and eyes. • Wear suitable loose-fitting, long-sleeved clothing. • Wear gloves and eye protection. • Consult Occupational Health and Safety Authority for any further information. AFTER HANDLING • Rinse any exposed skin areas with clean water. • Wash work clothing separately. FIRST FIRING OF HEATER • Fumes and smoke may be produced. • Avoid breathing fumes, ventilate area to clear. • Production of smoke should cease within 30 minutes REMOVAL OF USED PRODUCT • Wear an approved mask. Over-exposure to dust formed after service may cause respiratory disease since cristobalite, a form of crystalline silica may be formed above 900 degrees Celsius. • Consult Occupational Health and Safety Authority for further information regarding removal of used ceramic fibre linings. 5 Raypak Commercial Swimming Pool Heaters Part 2: Models 538 to 4224 6 PART 2 - SECTION I - INSTALLATION INSTRUCTIONS Raypak recommends a minimum length of vertical flue of three (3) metres to ensure correct draft. AGA Approved Cowl Distance above roof must be as stated in AG601 Self-supporting flue Bolted sleeve Correct draft converter (Indoor hood) Minimum flue length 3 metres Heater OUTDOOR INSTALLATIONS. An outdoor heater must not be installed inside any roofed structure or under eaves, roof overhangs, or pool decks. It should also be at least 1500 mm, in any direction from any window or fresh air opening. When installing the heater on a raised base, please make sure that the base material is solid and filled in. E.G. If steel mesh decking is used, a suitable plate material must be used to fill in the perforations. This is very important, as any excessive drafts must not be able to enter the unit from directly underneath. Water Connections Gas Connection This area must be filled in • On large elevated decks fill in to at least one metre all around unit Elevated Deck HIGH WIND CONDITIONS On rare occasions or in areas where high winds frequently occur, it may be necessary to locate the heater a minimum of one (1) metre from high vertical walls, or install a wind break so that the heater is not in direct wind current. Models 538 to 1852, where the installation may cause "Down draft", Raypak can supply a Wind Deflection Plate (at extra cost), to eliminate constant ignition failures or flame disturbance, the need for which would be determined by an approved Raypak Service Person or Agent. Wind Deflection Plate Prevailing Winds High Wind Windbreak In areas of "consta...