Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
This filter pump system has been manufactured to the highest quality standards, and will provide seasons of clean, sparkling-clear water activity in your new Simple-SetTM Pool. This Simple-SetTM Easy-Clean Filter Pump System Manual will provide you with all of the easy instructions you need to follow in order to set up and operate this state-of-the-art filter pump system efficiently. In addition to set-up instructions and operational guidelines, we have also included several very important Warning and Caution statements that pertain to the safe use and enjoyment of this new filter pump system. It is very important that you take the time to read them all and share them with any individuals that will ultimately be enjoying the use of your Simple-SetTM Pool. Please make certain that you read and understand the information contained in this Manual prior to initial use. Please retain this Manual for future reference. If you should have any questions regarding set-up and operation of your Easy-Clean filter pump system, you can easily reach our customer service Toll-Free (in the U.S.A.) number during the business hours of 8:00AM to 5:30PM EST. -2 Safety Instructions The following important points should be read and understood prior to use: 1. WARNING To prevent possible electric shock, do not attempt to plug in power cord with wet hands or while standing in water. 2. WARNING To prevent possible electric shock, connect power cord into a grounded receptacle protected by a ground-fault circuit interrupter (GFCI). 3. WARNING To prevent possible electric shock, never use a damaged or frayed power cord. 4. WARNING This filter pump is not intended for use by children. Adult assembly and operation required. 5. WARNING Do not bury the power cord. Locate it where it will not be damaged by lawn mowers, hedge trimmers or other equipment. 6. WARNING Do not use extension power cords with this product. 7. WARNING Make certain before each use of pump that all clamps are tightened and that all hoses are connected properly.. 8. WARNING Do not use this filter pump to vacuum pool. 9. WARNING This filter pump is designed for use only with storable pools. It must not be used with permanently installed pools. -3 -4- SA-3766 ITEM NO ITEM DESCRIPTION QTY P1 Air valve cover 1 P2-1,P2-2 Air valve pin 2 P3 Air valve screw 1 P4 Filter chamber cover 1 P5 Filter chamber rubber gasket 1 P6 Filter 1 P7 Pump chamber end cover nut 1 P8 Body 1 P9 Pump chamber end cover sealing flat gasket 1 P10 Pump chamber end cover 1 P11 Pump chamber end cover sealing 1 P12 Rubber shaft base 2 P13 Plastic ring 2 P14 Impeller 1 P15 Magnet rotor 1 P16 Motor shaft 1 P17 Pump body and motor stator assembly 1 P18 Water valve 1 P19 Wire cover 1 P20 Pump top cover 1 P21 Power cable 1 P22 Water pump fix screw (M4x30x4) 4 P23 Outlet flat gasket 1 P24 Outlet rubber ring 1 P25 Outlet pipe 1 P26 Outlet O ring 1 P27 Inlet O ring 1 P28 Connector Hose 2 P29 Metal Hose Clamp 4 -5 Installation Instructions 1. Prior to set-up and installation of filter pump, you must first set up the Simple-SetTM Pool and fill it completely with water, exactly following the Simple-SetTM Pool Manual instructions for pool set-up. 2. For optimal filter pump performance, position the filter pump unit at least 8 inches below the highest water level in the pool. 3. Keep the position of the filter pump unit at least 2 feet away from the sidewall of the pool itself. 4. Place clean filter cartridge (P6) into the body of the filter pump (P8). 5. Make certain that the filter chamber rubber gasket (P5) is placed in seal groove at top of filter pump body (P8). 6. Screw on filter chamber cover (P4) onto top of the body of filter pump (P8) in a clockwise direction by hand until it is secure. 7. Connect one end of hose (P28) to Inlet (upper) port of pump using one hoseclamp (P29). 8. Tighten hoseclamp securely with screwdriver. 9. Connect other end of hose (P28) lower protruding hose fixture on wall of pool, using one hoseclamp (P29). 10. Tighten hoseclamp securely with screwdriver. (Be careful to stay away from sidewall/liner when using screwdriver). 11. Connect one end of second hose (P28) to Outlet (lower) port of pump using one hoseclamp (P29). 12. Tighten hoseclamp with screwdriver. 13. Connect other end of second hose (P28) to upper protruding hose fixture on wall of pool, using one hoseclamp (P29). 14. Tighten hoseclamp securely with screwdriver. 15. Open both wall plug caps (P34) on the inside of the pool and plug in a strainer (P35) for each. 16. Allow time for filter pump chamber to fill with water. Never operate the filter pump dry. 17. Connect electrical power cord (P21) into a grounded receptacle protected by a ground-fault circuit interrupter (GFCI). Please contact a qualified electrician for verification purposes and/or installation of a GFCI receptacle if necessary. -6 -7- INSTALLATION ILLUSTRATION P29 P35 P34 P28 P29 P29 UPPER PROTRUDING HOSE CONNECTION LOWER HOSE INSIDE OF POOL (ILLUSTRATION NOT ...