Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
5/32 in. 95VP :4.8 mm dia. 3/16 in. Important points for proper maintenance of saw chain: • Keep the cutters sharp at all times. • Keep the left and the right cutters properly aligned. -Note that blunt or irregular cutters will result in poor cutting performance, increased vibration of chains and premature breakage of the saw chain. • Drive link serves to remove sawdust from the groove of the guide bar. Keep the lower edge of the drive link sharp where indicated. SETTING SAW CHAIN • For setting saw chain, round file (33SL : 4.0 mm dia. 5/32 in. or 95VP : 4.8 mm dia. 3/16 in.) and flat file are used. • To keep correct position and correct angle, use the file holder (Sure Sharp®). 10° Hold the file tipped 10° upward 27 CS-530 Side plate angleTop plate filing angle Parallel 0.64 mm (0.025 in.) Top plate cutting angle Depth gauge Remove until flat with tool Depth gauge tool Round off the edge 1/5 One fifth of file diameter remains above cutter edge 60° 33SL:25° 95VP:30° 33SL:60° 95VP:85° Side plate angleTop plate filing angle Parallel 0.64 mm (0.025 in.) Top plate cutting angle Depth gauge Remove until flat with tool Depth gauge tool Round off the edge 1/5 One fifth of file diameter remains above cutter edge 60° 33SL:25° 95VP:30° 33SL:60° 95VP:85° • Place the depth gauge tool firmly on guide bar so that depth gauge protrudes. Then file top of depth gauge with the flat file until flat with top of the depth gauge tool. -Be sure to round off the front edge of the depth gauge. Properly filed cutters are shown in illustration. When setting of the chain is finished, soak it in oil and wash away filings completely before using. -When chain has been filed on the bar, supply sufficient oil to it, rotate the chain slowly to wash away the filings before using again. -If the chain saw is operated with filings clogged in the groove, the saw chain and the guide bar will be damaged prematurely. -If the saw chain becomes soiled with resin, for instance, clean it with kerosene and soak in it oil. NOTE These angles are referred to as Oregon 33SL or 95VP. To sharpen other follow chain manufacturer’s instruction. CS-530 28 TROUBLESHOOTING Problem Engine — hard to start Cause Remedy — does not start Engine Fuel at No fuel • Fuel filter clogged • Clean or replace cranks carburetor at carburetor • Fuel line clogged • Clean • Carburetor • Ask your ECHO dealer Fuel at No fuel at • Carburetor • Ask your ECHO dealer cylinder cylinder Muffler wet • Fuel mixture is too rich • Open choke with fuel • Clean/replace air filter • Adjust carburetor • Ask your ECHO dealer Spark at No spark at • Ignition switch off • Turn switch on end of end of plug • Electrical problem • Ask your ECHO dealer plug wire wire • Spark gap incorrect • Adjust 0.6 mm to 0.7 mm Spark at No spark at (0.024 to 0.028 in.) plug plug • Covered with carbon • Clean or replace • Fouled with fuel • Clean or replace • Spark plug defective • Replace plug Engine • Internal engine problem • Ask your ECHO dealer does not crank Engine Dies or • Air filter dirty • Clean or replace runs accelerates poorly • Fuel filter dirty • Clean or replace • Fuel vent blocked • Clean • Spark plug • Clean and adjust/replace • Carburetor • Adjust • Cooling system blocked • Clean • Exhaust port/spark • Clean arrestor screen blocked WARNING Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result. 29 CS-530 STORAGE AFTER USE • Inspect and adjust every part of the chain saw. -Completely clean every part and repair if necessary. - Apply thin coating of oil on metal parts to prevent rust. • Remove chain and guide bar. • Drain fuel tank, pull starter slowly a few times to drain fuel from carburetor. • Pour a small amount of clean motor oil into spark plug hole, pull starter and crank the engine until piston reaches: TOP DEAD CENTER. • Store in a dry area, free from dust. WARNING Do not store in an enclosure where fuel fumes may accumlate or reach an open flame or spark. CAUTION Do not lend or rent your chain saw without the Instruction manual and Safety manual. NOTE • For future reference, you should keep this Instruction manual and the Safety manual. • If this Instruction manual or the Safety manual has become illegible or is lost, please purchase a new one from your ECHO dealer. TECHNICAL DATA CS-530 Dimension L . W . H mm 400 . 252 . 278 (15.7 in. . 9.9 in. . 10.9 in.) Mass Power head, dry kg 5.1 (11.2 lb.) Without chain and guide bar Engine Type Air-cooled two-stroke single cylinder Displacement mL (cm.) 50.1 (3.057 cu. in.) Carburetor Magneto Spark plug Starter Power transmission Diaphragm type Flywheel magneto: CDI system NGK BPM8Y Recoil starter Automatic centrifugal clutch Fuel Mixture ratio 50 : 1 ratio with ECHO Power Blend X™, ISO-L-EGD (ISO/CD 13738), JASO M345-FC/FD two- stroke, air-cooled engine oil. Gasoline Use 89 octane unleaded. Do not use fuel contain...