Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. Front Handle Located at front of saw body. Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain. Guide Bar Nose Tip or end of guide bar. Kickback Quick backward and upward motion of guide bar. Kickback may occur when tip of guide bar touches an object while chain is moving. The guide bar will kick up and back towards operator. Limbing Process of cutting limb(s) from a felled tree. Low-Kickback Chain Chain that reduces chance of kickback as required by CSA Standard Z62.3. Normal Cutting Position Stance used while making bucking and felling cuts. Notching Cut Notch cut in tree that directs fall of tree. Oiler Control System for oiling guide bar and chain. Power Head Chain saw without chain and guide bar. Also known as saw body. Pushback (Kickback, Pinch) Rapid pushback of chain saw. Pushback may occur if chain along top of guide bar is pinched, caught, or contacts a foreign object. Rear Handle Handle located at rear of saw body. Reduced Kickback Guide Bar Guide bar that reduces chance of kickback. Replacement Chain Chain that complies with CSA Standard Z62.3 when used with a specific saw. It may not meet CSA requirements when used with other saws. Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor drives chain. The guide bar supports chain. Spiked Bumper (Spike) Pointed teeth at front of saw body beside guide bar. Keep spiked bumper in contact with wood when felling or bucking. It helps maintain position of saw while cutting. Sprocket Toothed wheel that drives chain. Switch Device that completes or interrupts electrical circuit to motor of saw. Switch Linkage This device connects switch to trigger. It moves switch when you squeeze trigger. Switch Lockout Device that reduces accidental starting of saw. Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. 5 For more information, visit ® ® ELECTRIC CHAIN SAW PRODUCT IDENTIFICATION Power Cord Rear Hand Guard Rear Handle Front Hand Guard Guide Bar Sprocket Cover Saw Chain Guide Bar Nose Scabbard Figure 2 - Electric Chain Saw Oil Cap With Squeeze Bulb TriggerSwitch LockoutMotor Housing (located on saw body, hidden by front handle) Front Handle Spike UNPACKING 1. Remove all items from carton. 2. Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought chain saw. Oil Level Sight Hole ASSEMBLY Note:Some models are pre assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment, page 8. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. The plastic hardware bag should include: • two guide bar bolts • two guide bar nuts • one Phillips-head tapping screw 1. Lay chain out flat. 2. Install front hand guard onto saw body. Do this by pressing two mounting standouts on hand guard into hex-shaped holes in saw body (see Figure 3, page 7). 3 Insert tapping screw through hand guard and into saw handle. Tighten screw firmly. 4. Turn adjusting screw counterclockwise (see Figure 4, page 7). Continue to turn adjusting screw until adjusting block is to rear of adjusting plate. 5. Install guide bar onto saw body. Place rear of guide bar between adjusting plate and sprocket support. IMPORTANT:Make sure to insert adjusting block into oval adjusting hole on guide bar. 6. Line up holes on sprocket support with center slot on guide bar and holes in saw body. 7. Insert guide bar bolts through front hand guard, saw body, center slot of guide bar, and sprocket support. Attach guide bar nuts to guide bar bolts. IMPORTANT: Tighten guide bar nuts finger tight only. Make sure adjusting block is in oval adjusting hole on guide bar. 8. Place chain around drive sprocket, then along top groove of guide bar and around guide bar nose. Note: Make sure cutting edges of chain are facing the right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 3, page 7). CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. 9. Adjust saw chain tension. Follow steps under Saw Chain Tension Adjustment, page 8. IMPORTANT: Do not clamp chain saw in vise during assembly. For more information, visit 6 OWNER’S MANUAL ASSEMBLY Continued Mounting Stand-Outs Guide Bar Bolts Guide Bar Nuts Adjusting Hole Guide Bar Tapping Screw Saw Chain Towards Guide Bar Nose Front Hand Guard Drive Sprocket Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Cutting Edge Adjusting Block Figure 4 - Part Locations For Assembling Guide Bar Adjusting Plate Adjusting Screw Sp...
Este manual também é adequado para os modelos :Benzo e serras - EL-7 16-inch, EL-7 14-inch, LNT-3 12-inch, LNT-3 10-inch, LNT-2 10-inch, LNT-2 8-inch (2.07 mb)
Benzo e serras - LNT-2 EL-7 16-inch, EL-7 14-inch, LNT-3 12-inch, LNT-3 10-inch, LNT-2 10-inch, LNT-2 8-inch (2.07 mb)
Benzo e serras - LNT-2 EL-7 16-inch, EL-7 14-inch, LNT-3 12-inch, LNT-3 10-inch, LNT-2 10-inch, LNT-2 8-inch (2.07 mb)