Assessments - 5, GPA: 4.4 ( )

Fabricante : Remington Arquivo Tamanho: 606.94 kb Arquivo Nome : Língua de Ensino:

With flat file, round off front corner of cutter depth gauge (see Figure 23). After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing. Figure 22 - Depth Gauge Tool On Chain Flat File Depth Gauge Slot Figure 23 - Round Off Front Corner Of Depth Gauge Depth Gauge Tool Depth Gauge Front Corner .025" CLEANING AND MAINTENANCE Continued WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with moving chain. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Do not handsharpen this Fast Sharp chain. Hand-sharpening chain will increase risk of kickback. Figure 24 - Turning Sharpener Knob Keep chain sharp. Your saw will cut faster and more safely. A dull chain will cause undue sprocket, guide bar, chain, and motor wear. If you must force chain into wood and cutting creates only sawdust with few large chips, chain is dull. Follow the steps below to sharpen Fast Sharp chain. The automatic chain sharpener sharpens cutter, lowers cutter depth gauge, and adjusts guard drive link. 1. Adjust saw chain for proper tension (see Saw Chain Tension Adjustment, page 7). 2. Clean out excess sawdust and wood chips from drive sprocket area. 3. Turn sharpener knob counterclockwise until clicking stops (see Figure 24). 4. Turn sharpener knob clockwise until you hear five distinct clicks. SHARPENING SAW CHAIN (Fast Sharp Model) Figure 25 - Sharpening Fast Sharp Chain Sharpener Knob REPLACING SAW CHAIN Replace chain when cutters are too worn to sharpen or when chain breaks. Only use replacement chain noted in this manual. Always include new drive sprocket when replacing chain. This will maintain proper driving of chain. Note: For proper chain and drive sprocket, see Replacement Parts and Accessories, on back cover. 5. Place saw on clean, flat surface. 6. Connect saw to power supply. 7. Hold saw, with both hands in normal cutting position. 8. Press in switch lockout with right thumb and squeeze trigger. 9. Gently push on sharpener knob. Saw must be running for chain to sharpen. Note: Sparks appearing shows sharpener is working (see Figure 25). If no sparks appear, continue to adjust sharpener one click at a time. After each click, press sharpener knob until light flow of sparks appears. After several sharpenings, you must turn sharpener knob more to bring stone into position. OWNER’S MANUAL WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with moving chain. OBSERVED FAULT POSSIBLE CAUSE REMEDY Saw runs, but does not cut. Chain assembled backwards on guide bar See Assembly, page 6 Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips. Chain is dull See Sharpening Saw Chain, page 13 (non- Fast Sharp model) or page 14 (Fast Sharp model) Saw runs slow. Saw stalls easily. Low power supply voltage Extension cord wire size too small. See Extension Cords, page 8 Motor of saw does not run when you squeeze trigger. 1. Switch lockout not pressed in to release trigger 2. Extension cord connections loose 3. Open line fuse or circuit breaker 4. Bad motor brushes 5. Open wiring circuit on saw 1. Press in switch lockout before squeezing trigger 2. Check cord connections 3. Check line fuse or circuit breaker 4. See authorized service center 5. See authorized service center Motor of saw runs, but chain does not move. Gear train failure See authorized service center Chain does not get oil. 1. Clogged oil slot in guide bar 2. Oil is too thick 1. Remove guide bar and clean oil slot 2. Use correct weight of oil. See Filling Oil Tank, page 7 Chain comes off guide bar. 1. Chain is loose 2. Guide bar and chain not assembled right 1. Tighten chain. See Saw Chain Tension Adjustment, page 7 2. See Assembly, page 6 Saw smokes. Saw damaged. Do not use saw. See authorized service center TROUBLESHOOTING Saw leaks oil. STORAGE If storing saw for more than 30 days, follow steps below. 1. Drain oil tank. 2. Remove and clean guide bar and chain. Clean guide bar and chain by soaking in petroleum based solvent or mild soap and water mixture. 3. Dry guide bar and chain. 4. Place chain in container filled with oil. This will prevent rust. 5. Wipe a thin coating of oil over surface of guide bar. Oil cap is not secure. 6. Wipe off outside of saw body. Do this with soft cloth dampened with a mild soap and water mixture. 7. Store chain saw • in a high or locked place, out of children’s reach • in a dry place • in a carrying case or with scabbard over guide bar TECHNICAL SERVICE You may have further questions about assembling, operating, or maintaining this saw. If so, contact DESA International’s Technical Service Department at 1-800-323-5190. Tighten oil cap. Note: Empty oil tank when not in use. SERVICE PUBLICATIONS You can buy a service manual from address l...

Baixe o seu

Para fazer o download, introduza 2 dígitos :