Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
If the extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor use can also be used for indoor work. The letters “W” or “WA” on the cord jacket indicate that the cord is suitable for outdoor use. b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size. CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS NAMEPLATE RATING AMPS – 0 – 10.0 Cord AWG Cord Length Size 25 feet 18 AWG 50 feet 18 AWG 100 feet 16 AWG 150 feet 14 AWG 7. Use only the supplied charger (P/ N 121397-01)when charging. The use of any other charger could damage the battery or create a hazardous condition. 8. Use only one charger when charging. 9. Use only Remington RB18V OR RBE18V battery packs with this product. 10. Do not attempt to open the charger. There are no customer serviceable parts inside. If damaged, call DESA Power Tools Technical Service. 11. DO NOT incinerate the battery pack even if they are severely damaged or completely worn out. The batteries can explode in a fi re. 12. A small leakage of liquid from the battery pack cells may occur under extreme usage, charging, or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: • Wash quickly with soap and water. • Neutralize with a mild acid such as lemon juice or vinegar. • If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. ENGLISH 9 RECHARGEABLE BATTERY CHARGING BATTERY The battery pack is not fully charged at the factory. Before attempting to charge the battery pack, thoroughly read all Safety Instructions. The charger is designed to use standard household 120 volt 60 Hz power. 1. Plug cord from charger into charger base. (See Figure 2) Figure 2 - Plug Charger into Base 2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. IMPORTANT: Do not charge by means of an engine generator or DC power source. Use only 120V AC. 3. Slide the charger onto the battery pack as shown in Figure 3. The LED will light up, Let the battery pack charge until red LED turns off. After the initial charge, under normal usage, your battery pack should be fully charged in 3 to 9 hours. Figure 3 - Slid Charger onto Battery 4. Unplug charger. Remove the charger by sliding off (See Figure 4). 5. Place the battery pack in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place. Figure 4 - Remove Charger IMPORTANT CHARGING NOTES 1. After normal usage, your battery pack should be fully charged in 3 to 9 hours. If the battery pack is run-down completely, it may take up to 9 hours to become fully charged. Your battery pack was sent from the factory in an uncharged condition. For best performance charge battery until red LED turns off. Allow the battery to cool down 30 minutes before charging after using the saw. NOTE: A hot battery placed in the charger will not charge. 2. DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above 105°F (40,5 °C). This is important and will prevent serious damage to the battery pack. Longest life and best performance can be obtained if battery pack is charged when air temperature is about 75°F (24°C). 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem. 4. If the battery pack does not charge properly • Check current at receptacle by plugging in a lamp or other appliance. • Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. • Move charger and battery pack to a surrounding air temperature of 40°F (4,5°C) to 105°F (40,5 °C) • If the receptacle and temperature are OK, and you do not get proper charging contact DESA Power Tools. 5. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its battery pack in a depleted condition. 6. To prolong battery life, avoid leaving the battery pack on charger for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can signifi cantly reduce overall battery life. 7. The battery pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. 10 CHAIN SAW INFORMAT...
Este manual também é adequado para os modelos :Benzo e serras - BPS188A (3.35 mb)
Benzo e serras - BPS188A (3.35 mb)
Benzo e serras - BS188A (3.35 mb)