Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
MINIMUM WIRE GAUGE RECOMMENDATIONS Volts 25 ft. (7.67 m) 50 ft. (15.24 m) 100 ft. (30.48 m) 120 16 A.W.G.* 16 A.W.G.* 14 A.W.G.* PowerCordExtensionCord *American Wire Gauge 7 BEFORE STARTING SAW WARNING: Be sure to read the electrical safety information in the SAFETY RULES section of this manual before you begin. If you do not understand the electrical safety information do not attempt to use your unit. Seek help from someone that does understand the information or call the customer assistance help line at 1-800-554-6723. GUIDE BAR AND CHAIN OIL The bar and chain require lubrication. The manually- --operated chain oiler provides lubrication to the chain and guide bar. Be sure to fill the bar oil tank before each cutting session. The oiler activator/bar oil cap must be used regularly and often enough to maintain a thin film of oil on the bar and chain while saw is cutting. It is recommended that the oiler actuator/bar oil cap be operated every ten (10) seconds and held for approximately three (3) seconds each time it is pressed. For maximum guide bar and chain life, we recommend you use Poulan chain saw bar oil. If Poulan bar oil is not available, you may use a good grade SAE 30 oil until you are able to obtain Poulan brand. The oil output is manually metered during operation. Use a funnel to fill the tank. Replace oil cap securely. Check oil level after every 15 minutes of operation. STOPPING YOUR SAW S Release the trigger switch. S If motor does not stop, disconnect the extension cord. Discontinue use of the unit until repaired by an authorized service dealer. STARTING YOUR SAW 1. Connect the saw to a power source using the proper size extension cord (see SELECT AN EXTENSION CORD). 2. Push in switch lock out button. 3. Squeeze and hold the trigger switch. CUTTINGMETHODS OPERATING TIPS S Check chain tension before first use and after 1 minute of operation. See CHECK CHAIN TENSION in the MAINTENANCE section. S Cut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc. S Stop the saw if the chain strikes a foreign object. Inspect the saw and repair parts as necessary. S Keep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and increase the possibility of kickback. S Practice cutting a few small logs using the following steps. This will help you get the “feel” of using your saw before you begin a major sawing operation. S Squeeze the trigger switch and allow unit to reach full speed before cutting. S Begin cutting with the saw frame against the log. S Keep the motor at full speed the entire time you are cutting. S Release trigger switch as soon as cut is completed, allowing motor to stop. S Keep the cord away from the cutting area. Position cord so it will not be caught on branches and the like during cutting. S To avoid losing control when cut is complete, do not put pressure on saw at end of cut. S Stop motor before setting saw down. 8 TREE FELLING TECHNIQUES WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near buildings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be able to see well, nor during bad weather such as rain, snow,strong winds,etc.Ifthe tree makes contact with any utility line, the utility complany should be notified immediately. S Carefully plan your sawing operation in advance. S Clear the work area. You need a clear area all around the tree so you can have secure footing. S The chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled. S Study the natural conditions that can cause the tree to fall in a particular direction, such as: S The wind direction and speed. S The lean of the tree. The lean of a tree might not be apparent due to uneven or sloping terrain. Use a plumb or level to determine the direction of tree lean. S Weight and branches on one side. S Surrounding trees and obstacles. S Look for decay and rot. If the trunk is rotted, it can snap and fall toward the operator. S Make sure there is enough room for thetreetofall. Maintain a distanceof 2-1/2 tree lengths from the nearest person or other objects. Motor noise can drown out a warning call. S Remove dirt, stones, loose bark, nails, staples, and wire from the tree where cuts are to be made. 45_ Planaclearretreatpath Direction of Fall FELLING LARGE TREES (6 inches in diameter or larger) The notch method is used to fell large trees. A notch is cut on the side of the tree in the desired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend to fall in the direction of the notch. NOTE: If tree has large buttress roots, remove them before making the notch. If using saw to remove buttress roots, keep saw chain from contacting ground to prevent dulling of the chain. NOTCH CUT AND FELLING TREE S Make notch cut by cutting the top of the notch first...
Este manual também é adequado para os modelos :Benzo e serras - 1630 (213.43 kb)