Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Special measures are therefore often required: • Partly mask the air inlet on the starter to increase the working temperature of the engine. Temperature 0°C (32°F) or colder: The cylinder cover is designed so it can be adjusted for running in cold weather. Twist the winter flap so that preheated air from the cylinder can pass into the carburettor space preventing icing of the air filter, etc. Temperature -5°C (23°F) or colder: For temperatures below -5°C and/or in snow conditions there is also: • a special cover (A) for the starter housing • a winter plug (B) for the air nozzle that is fitted as shown. These reduce the flow of cooling air and prevent large amounts of snow from being sucked into the carburettor space. CAUTION! When the winter plug is fitted the winter flap must be open! Below you will find some general maintenance instructions. Daily maintenance 1 Check the throttle trigger for smooth operation. If any binding occurs, or if engine fails to return to idle, the machine should be taken to your dealer, befor it is used again. Also, be sure that the trigger cannot be pulled until the throttle trigger lockout is depressed. 2 Clean the chain brake and check that it operates safely. Make sure that the chain catcher is undamaged, and replace it if necessary. 3 Clean the air filter. Replace if necessary. 4 The bar should be turned daily for more even wear. Check the lubrication hole in the bar, to be sure it is not clogged. Clean the bar groove. If the bar has a sprocket tip, this should be lubricated. 5 Check that the bar and chain are getting sufficient oil. 6 Sharpen the chain and check its tension and condition. Check the drive sprocket for excessive wear and replace if necessary. 7 Clean the air intake on the starter. Check the starter and starter cord for wear or damage. 8 Check that nuts and screws are tight. 9 Test the stop switch to be sure it shuts off the engine. 10 Check the cooling system on chain saws with catalytic converters. IMPORTANT! If the special winterising kit has been fitted or any measures have been taken to increase the temperature these changes must be reversed before the machine is used in normal temperature conditions. Otherwise there is a risk of overheating, resulting in severe damage to the engine. IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer). H H 7 8 6 1 2 3 4 5 9 10 English – 33 MAINTENANCE Weekly maintenance 1 Check that the vibration damping elements are not damaged. 2 Lubricate the clutch drum bearing. 3 File off any burrs from the edges of the bar. 4 Clean the spark plug. Check that the electrode gap is 0.5 mm (0,020 inch). 5 Clean the fins on the flywheel. Check the starter and the recoil spring. 6 Clean the cooling fins on the cylinder. 7 Clean or replace the spark arrestor mesh in the muffler. 8 Clean the carburettor compartment. Monthly maintenance 1 Check the brake band on the chain brake for wear. 2 Check the clutch centre, clutch drum and clutch spring for wear. 3 Clean the outside of the carburettor. 4 Change the fuel filter in fuel tank. 5 Clean the inside of the fuel tank. 6 Clean the inside of the oil tank. 7 Check all cables and connections. 8 Change the spark plug. 9 Change the air filter. 5 8 1 2 3 4 6 0,5 mm 7 1 3 8 9 0,5 mm TECHNICAL DATA Technical data CS 2141 CS 2145 CS 2150 Engine Cylinder volume, cu.in/cm3 2,49/40,8 2,75/45,0 3,15/51,7 Cylinder bore, inch/mm 1,57/40 1,65/42 1,77/45 Stroke, inch/mm 1,28/32,5 1,28/32,5 1,28/32,5 Idle speed, rpm 2700 2700 2700 Power, kW/ rpm 2,0/9000 2,2/9000 2,3/9000 Ignition system Manufacture SEM SEM SEM Type of ignition system CD CD CD Spark plug NGK BPMR 7A NGK BPMR 7A NGK BPMR 7A Champion RCJ 7Y Champion RCJ 7Y Champion RCJ 7Y Electrode gap, inch/mm 0,02/0,5 0,02/0,5 0,02/0,5 Fuel and lubrication system Manufacturer of carburettor Zama Zama Zama Carburettor type C3-EL18 C3-EL18 C3-EL18 Fuel tank capacity, US pint/litre 1,06/0,5 1,06/0,5 1,06/0,5 Oil pump capacity at 9,000 rpm, ml/min 9 9 5-12 Oil tank capacity, US pint/litre 0,53/0,25 0,53/0,25 0,53/0,25 Type of oil pump Automatic Automatic Automatic Weight Chain saw without bar or chain, empty tanks, Lbs/kg 10,8/4,9 10,8/4,9 10,8/4,9 Chain/bar Standard bar length, inch/cm 13"/33 13"/33 13"/33 Recommended bar lengths, inch/cm 13-18”/33-45 13-18”/33-45 13-18”/33-45 Usable cutting length, inches/cm 12-17"/31-43 12-17"/31-43 12-17"/31-43 Chain speed at max. power, m/sec 17,3 17,3 17,3 Pitch, inch/mm 0,325/8,25 0,325/8,25 0,325/8,25 Thickness of drive links, inch/mm 0,050/1,3 0,050/1,3 0,050/1,3 0,058/1,5 0,058/1,5 0,058/1,5 Number of teeth on drive sprocket 7 7 7 34 – English TECHNICAL DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Jonsered chain saw models 2141, 2145 and 2150.The combinations of power head, bar and chain have been investigated in accordance with the kickback and vibration requirements...
Este manual também é adequado para os modelos :Benzo e serras - CS 2141 EPA II (2.02 mb)
Benzo e serras - CS 2150 EPA I (2.02 mb)