Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
• Sanding should be done in a manner to reduce tracking of paint dust outside the work area. Cleaning and Disposal • All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. • Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Motor Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply. Operating Instructions WARNING: Always unplug sander from power supply before any of the following operations. WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using this tool. Attaching Sandpaper To attach sandpaper, carefully center the cloth side of the paper over the sanding pad. Press the paper firmly in place. The hook and loop paper can be removed by simply pulling it off. Switch - Figure 1 To turn the tool ON, push the portion of the dust protected switch marked "I". To turn the tool OFF, push the portion of the switch marked "O". Holding the Sander - Figures 2, 3, 4 The design of the Random Orbit Sander allows for several different gripping methods. Three basic methods are: Figure 2 - One handed operation on the top of the sander. Figure 3 - One handed operation holding the body of the sander. Figure 4 - Two handed operation with one hand on the jug handle and the other on the body or the top of the sander. Operation Grasp the sander and turn it ON. Move it in long, sweeping strokes along the surface, letting it do the work. Utilize an even pressure across the sanding pad. Excessive pressure in the corner area may cause damage. Pushing down on the tool while sanding actually slows the removal rate and produces an inferior quality finish. Check your work often. Sander is capable of removing material rapidly. Dust Extraction - Figure 5, 6 WARNING: Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty bag frequently and strictly follow sander manual and coating manufacturer's instructions. Your sander comes equipped with a cloth dustbag to collect the dust generated while sanding. To attach the dustbag onto the sander simply slide it firmly into the dust extraction port at the back of the sander. To empty the dust dustbag, remove it from the sander by pulling it straight back. Dump the sanding debris into an appropriate trash receptacle. You may, if you prefer, attach a vacuum cleaner to the tool to collect the dust as you sand. A vacuum hose adaptor is available as a service part at extra cost. To find your nearest Black & Decker Service Center location, refer to the yellow pages directory under "Tools— Electric" or call: 1-800-544-6986. To use the adaptor, remove the dust bag and replace it with the adaptor, then install a vacuum hose. Ensure that the vacuum cleaner can be placed such that it will not tip over or interfere with the motion of the sander. If this cannot be done, do not use the vacuum cleaner. Turn on the vacuum cleaner before beginning to sand and turn it off after turning off the sander. Empty vacuum cleaner as required. Maintenance / Cleaning Use only mild soap and damp cloth to clean the tool. Many household cleaners contain chemicals which could seriously damage the plastic and gel components. Also do not use gasoline, turpentine, lacquer or paint thinners or similar products. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Cord not plugged in. • Plug tool into a working outlet. • Circuit fuse is blown. • Replace circuit fuse. (If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.) • Circuit breaker is tripped. • Reset circuit breaker. (If the pro...