Assessments - , GPA:
(
)
)
Fabricante : RedMax
Arquivo Tamanho: 660.97 kb
Arquivo Nome : ZOUS2007-G3800AVS.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
This product has accordingly been designed with a ventilation hatch on the right side of the surface of the cylinder cover to allow warm air to be supplied to the engine and to thereby prevent icing from occurring. Under normal circumstances the product should be used in normal operating mode, i.e., in the mode to which it is set at the time of shipment. However when the possibility exists that icing may occur, the unit should be set to operate in anti-freeze mode before use.(F18) (1) Normal operating mode (2) Anti-freeze mode (3) Cylinder cover (4) ‘Sun shine’ mark (5) ‘Snow’ mark Continuing to use the product in anti-freeze mode even when temperatures have risen and returned to normal may result in the engine failing to start properly or in the engine failing to operate at its normal speed, and for this reason you should always be sure to return the unit to normal operating mode if there is no danger of icing occurring. WARNING F18 F17 .15 . WARNING F18 F17 .15 . 7. Operation F19 ¦ HOW TO SWITCH BETWEEN OPERATING MODES (F19) 1. Flip the engine switch to turn off the engine. 2. Remove the cover to the air filter, remove the air filter, and then remove the choke knob from the cylinder cover. 3. Loosen the screws holding the cylinder cover in place (i.e., the three screws on the inside and the one screw on the outside of the cover), and then remove the cylinder cover. 4. Press with your finger down on the icing cap located on the right-hand side of the cylinder cover to remove the icing cap. 5. Adjust the icing cap so that the ‘snow’ mark faces upwards and then return it to its original position in the cylinder cover. 6. Fix the cylinder cover back into its original position, and then fix all other parts back into their proper positions. (1) Choke knob (2) Cylinder cover (3) Icing cap .16 . 8. Sawing WARNING F21 • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. •Always follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vibrations and kickback vary with different materials and the requirements of the safety regulations would not be respected. Do not use the chain saw as a lever for lifting, moving or splitting objects. Do not lock it over fixed stands. It is forbidden to hitch tools or applications to the P.t.o. that are not specified by the manufacturer. •It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • When the saw chain is caught in the cut, do not attempt to pull it out by force, but use a wedge or a lever to open the way. ¦ GUARD AGAINST KICKBACK (F21) • This saw is equipped with a chain brake that will stop the chain in the event of kickback if operating properly. You must check the chain brake operation before each usage by running the saw at full the throttle for I -2 seconds and pushing the front hand guard forward. The chain should stop immediately with the engine at full speed. If the chain is slow to stop or does not stop, replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw. Removal of the safety devices, inadequate maintenance, or incorrect replacement of the bar or chain may increase the risk ot serious personal injury due to kickback. .17 . F22 F23 F24 F25 F26 .19 . .20 . 9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. ¦ MAINTENANCE AFTER EACH USE 1. Air filter Dust on the cleaner surface can be removed by tapping a corner of the cleaner against a hard surface. To clean dirt in the meshes, split the cleaner into halves and brush in gasoline. When using compressed air, blow from the inside. (F27) To assemble the cleaner halves, press the rim until it clicks. When installing the main filter, make sure that the grooves on the filter edge are correctly fit with the projections on the cylinder cover. 2. Oiling port Dismount the guide bar and check the oiling port for clogging. (F28) (1) Oiling port 3. Guide bar When the guide bar is dismounted, remove sawdust in the bar groove and the oiling port. (F29) Grease the nose sprocket from the feeding port on the tip of the bar. (F30) (1) Oiling port (2) Grease port (3) Sprocket NOTE WARNING F27 F28 F29 F30 NOTE WARNING F27 F28 F29 F30 F31 .21 . F34 F35 ¦ SAW CHAIN It is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra fo...
Este manual também é adequado para os modelos :Benzo e serras - G3800AVS (660.97 kb)