Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Specifications are subject to change without notice. REV0708 F/N 71904 853PRO OPERATOR’S MANUAL 3 TABLE OF CONTENTS SYMBOLS & LABELS 4 SAFETY 5 TECHNICAL SPECIFICATIONS 7 SET-UP 8 OPERATION 10 MAINTENANCE 12 TROUBLESHOOTING 14 REFERENCE 15 853PRO OPERATOR’S MANUAL 4 © 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904 SYMBOLS & LABELS THE FOLLOWING SYMBOLS AND DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. A potentially hazardous situation exists which, if not avoided, could result in death or serious injury. WARNING A potentially hazardous situation exists which, if not avoided, may result in minor or moderate injury or property damage. CAUTION A potential situation exists which, if not avoided, may result in product or property damage. IMPORTANT THE FOLLOWING SYMBOLS & LABELS MAY BE FOUND IN THIS MANUAL OR ON THE SAW Read the operator’s manual carefully and understand the contents before you use this equipment. Always use: • Protective helmet • Ear protection • Protective glasses or full face protection Wear hand protection .. WARNING • Inserting the tool into a pre-cut slot that is narrower than the chain may cause binding and rapid push-back of the tool toward the operator • Always operate tool with solid footing and firm hand grip • Contact at a hydraulic leak or burst can cause oil injection into the body • Do not exceed the hydraulic flow recommended for your saw model: 8 gpm, (30 lpm) or 12 gpm (45 lpm) at 2,500 psi (172.5 bar) hydraulic pressure • Minimum water pressure 20 psi (1.5 bar) • Weight 23 lbs (10.4 kg) w/out bar and chain READ OPERATIONS & MAINTENANCE MANUAL BEFORE USE OF TOOL. FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS PERSONAL INJURY SAFETY THE FOLLOWING SYMBOL APPLIES TO ALL THE ITEMS LISTED ON THIS PAGE WARNING A potentially hazardous situation exists which, if not avoided, could result in death or serious injury. Diamond chain breakage can result in high-speed ejection of parts, which can result in death or serious personal injury to operators or bystanders. The items listed below are critical to minimizing the risk of diamond chain breakage and injury. • DO NOT operate a diamond chainsaw with a damaged, modified, broken or missing side cover, bottom guard or guard flap. The side cover, bottom guard and guard flap provides protection against contact with moving parts, ejected debris, broken diamond chain, thrown water and concrete slurry. • DO NOT operate saw with loose, missing damaged or improperly repaired parts. • DO NOT exceed the hydraulic flow for your saw model: 8 gpm (30 lpm) or 12 gpm (45 lpm) at 2,500 psi (172.5 bar) hydraulic pressure. • DO NOT install or run the chain backwards. The bumper should lead the segment into the cut. • DO NOT run the saw backwards. The chain should travel away from the operator on the top of the bar and return on the bottom of the bar. • DO NOT insert the diamond chainsaw into a slot narrower than the chain segments. Rapid pushback might occur. Ref: Most diamond segements are .225 (5.72 mm) wide. • DO NOT use the 853PRO side cover as a replacement cover for another saw. • DO NOT run the saw upside-down. Concrete debris can fly back into the operator’s face. • NEVER cut ductile iron pipe with the saw. Segment loss or diamond chain breakage may occur. • DO NOT use your hands to search for hydraulic leaks. Hydraulic fluid escaping under pressure can penetrate skin. If any hydraulic flud is injected into skin seek medical attention immediately. Bumper SAFETY THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE CAUTION A potentially hazardous situation exists which, if not avoided, may result in minor or moderate injury or property damage. • Always turn the saw OFF when performing maintenance on the saw including diamond chain tensioning. • Never use equipment that is not functioning properly. Have the saw repaired by qualified service personnel. • Diamond chains require a minimum water pressure of 20 psi (1.5 bar). Insufficient water supply may result in excessive wear to the diamond chain, which can lead to loss of strength and diamond chain breakage. • Never start the saw unless the guide bar, diamond chain and side cover are properly installed. GENERAL SAFETY PRECAUTIONS • Always wear protective clothing, including hard hat, eye protection, hearing protection, and gloves. • Avoid loose fitting clothing. • Perform safety checks before starting each day. • Always operate tool with solid footing and with both hands on cut-off saw. • Remove or control slurry to prevent slippery conditions while cutting. • Be sure there are no obstructions (plumbing, electrical conduit, air ducts) and no unnecessary people present. • Set up a well-marked safety zone with a roped boundary and clear signs. • Provide adequate ventilation when working in an enclosed area. Breathing exhaust gases is dangerous. • To avo...
Este manual também é adequado para os modelos :Benzo e serras - 853PRO (753.03 kb)
Benzo e serras - 853PRO (753.03 kb)