Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
S Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back toward the operator. S Either of these reactions may cause you to lose control of the saw which could result in serious injury.Do not rely exclusively upon the safety devices built into your saw. WARNING: Computed kickback angle (CKA) listed on your saw and listed in the CKA table below represents angle of kickback your bar and chain combinations will have when tested in accordance with CSA and ANSI standards. When purchasing replacement bar and chain, considerations should be given to the lower CKA values. Lower CKA values represent safer angles to the user, higher values indicate more angle and higher kick energies. Computed angles represented in the non-activated column indicate total energy and angle associated without activation of the chain brake during kickback. Activated angle represents chain stopping time relative to activation angle of chain brake and resulting kick angle of saw. In all cases lower CKA values represent a safer operating environment for the user. The following guide bar and chain combinations meet kickback requirements of CSA Z62.1, Z62.3, & ANSI B175.1 when used on saws listed in this manual. Use of bar and chain combinations other than those listed is not recommended and may not meet the CKA requirements per standard. 5 6 Computed kickback angle (CKA) Table BAR P/N Length CHAIN P/N 952044370 14! 952051211 MODEL 952044418 16! 952051338 14_ CKA without chain brake 2250 2250/2450 19_ 2550 18! 952044368 952051209 24_ NOTE: If this saw is to be used for commercial logging, a chain brake is required and shall not be removed or otherwise disabled to comply with Federal OSHA Regulations for Commercial Logging. SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. SPECIALNOTICE: Your saw is equipped with a temperature limiting muffler and spark arresting screen which meets the requirements of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines to be equipped with a spark arresting screen. If you operate a chain saw in a state or locale where such regulations exist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. Refer to the SERVICE section for maintenance of the spark arresting screen. Failure to follow all Safety Rules and Precautions can result in serious injury. If situations occur which are not covered in this manual, use care and good judgement. If you need assistance, contact your authorized service dealer or call 1-800--554--6723. STANDARDS: This saw is listed byUnderwriter’s Laboratories, Inc., and the Canadian Standards Association in accordance with: ANSI B175.1-2000 American National Standard for Powered Tools -- Gasoline Powered Chain Saw -- Safety Requirements CSA Z62.1--1995 Chain Saws -- Occupational Health and Safety CSA Z62.3--1996 Chain Saw Kickback Occupational Health and Safety ASSEMBLY Protective gloves (not provided) should be worn during assembly. ATTACHING THEBAR&CHAIN (If not already attached) WARNING: If received assembled, repeat all steps to ensure your saw is properly assembled and all fasteners are secure. Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not moving! S Loosen and remove the chain brake nuts and the chain brake from the saw. S Remove the plastic shipping spacer (if present). Chain Brake Chain Brake Nuts Bar Tool Location of shipping spacer S Turn adjusting screw on bar counterclockwise to move the tensioning rack as far as it will go toward the front of the bar. Tensioning Rack Adjusting Screw S Slide the bar behind clutch drum until bar stops against clutch drum sprocket. Mount the Bar Tip of Bar TipofBar S Prepare the chain by checking the proper direction. Without following the illustration it is easytoplace thechainonthe saw inthe wrong direction. Use the illustration of the chain to determine the proper direction. CUTTERS MUST FACE IN DIIRECTION OF ROTATION Depth Gauge Cutters Drive Links S Place the chain over and behind the clutch, fitting the drive links in the clutch drum sprocket. Place chain...