Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
. . . . . . . . . . . .3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8 Product Tips . . . . . . . . . . . . . . . . . . . . . . . . .8-9 Consistency Control . . . . . . . . . . . . . . . . . .9-10 Care &Cleaning . . . . . . . . . . . . . . . . . . . .11-15 Maintenance . . . . . . . . . . . . . . . . . . . . . . .15-16 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . .17 Freezer Specifications . . . . . . . . . . . . . . . .18-19 Troubleshooting Guide . . . . . . . . . . . . . . .20-21 Exploded Views . . . . . . . . . . . . . . . . . . . . .22-30 Wiring Diagrams . . . . . . . . . . . . . . . . . . . .31-41 Refrigeration Schematic . . . . . . . . . . . . . . . . .42 Prior authorization must be obtained from Grindmaster Corporation for all warranty claims. Model 5512 Grindmaster Corporation 4003 Collins Lane Louisville, KY 40245-1643 Phone (502) 425-4776 800-695-4500 (USA & Canada only) (800) 568-5715 (technical service only) Fax (502) 425-4664 © Grindmaster Corporation, 2000 0106 Form #WH-332-04 PRINTED IN USA Part #W0600138 Operator's Safety Precautions 1. Read and understand the operating instructions in this manual thoroughly. 2. Note all warning labels on the freezer. If any warning labels are missing or damaged replace them immediately. 3. Do not wear loose fitting garments or jewelry which could cause a serious accident. 4. Stay alert at all times during operation. 5. Keep operating area clean. 6. Do not operate freezer if any excessive noise or vibration occurs. Contact your authorized service agent. Installation Shipment & Transit The freezer has been operated and tested at the factory. Upon arrival the complete freezer must be thoroughly checked for any damage which may have occurred in transit. Note: A Tip (N) Tell warning device is placed on each shipping carton at the factory. If the arrow tip is blue, the carton has been tipped in transit. Removal from Carton and Pallet 1. Remove staples or cut cardboard box around the stapled area. 2. Pull the cardboard box up off machine. 3. Remove the Styrofoam packing and the plastic bag. 4. Remove both side panels with screwdriver. 5. Use a wratchet with a 3 inch extension and a 7/16 socket to remove the shipping bolts (connecting the machine to the pallet) located on both sides of the frame bottom plate. 6. Supporting all four sides, lift machine up and place in appropriate area. THE CARRIER IS RESPONSIBLE FOR ALL DAMAGE IN TRANSIT WHETHER VISIBLE OR CONCEALED. DO NOT PAY THE FREIGHT BILL until the freezer has been checked for damage. Have the carrier note any visible damage on the freight bill. If concealed damage and/or shortage is found later, advise the carrier within 10 days and request inspection. The customer must place any claim for damage and/or shortage with the carrier. Grindmaster Corporation cannot make any claims against the carrier. CAUTION: IF EQUIPPED WITH SPINNER DO NOT LIFT UNIT BY SPINNER SHAFT TO AVOID SERIOUS ! DAMAGE TO SPINNER. Figure A Crathco® 5512 Manual Page 3 Figure D INSTALL THE FILTER PANEL OVER THE EXISTING SIDE PANEL & RE-INSTALL SCREWS. P/N: W0520101, COMES IN KIT # W0890220 FILTER PANEL P/N: W0631805 FILTER SLIDE THE FILTER IN BEHIND THE FILTER PANEL, & IN FRONT OF THE EXISTING SIDE PANEL. TO CHANGE REMOVE, CLEAN, & OR REPLACE. Installing Your Unit CAUTION: Do not alter or deform the plug in any way. Altering or deforming plug may damage unit ! and will void warranty! Receptacle NEMA 6-20R required for Model 5512. 1. Place freezer in a location that allows adequate space at each side and above for proper air circulation. Minimum clearance is: 6” (15 cm) on both sides, 4” (10 cm) at back, and 8" (20 cm) above the freezer. See figure B. CAUTION: Failure to allow adequate ventilation will void the warranty ! and reduce freezer performance. 2. Place the freezer on the self-sealing rubber pad on a level counter that is stable and strong enough to safely support its weight (276 lbs/124.2 kg). If equipped with legs instead of pad, install legs by screwing them into the four Figure B leg holes on the bottom of the unit. (Leg Kit Part #W089.0220 (4) 4” Legs.) Proper air clearance 3. Place On-Off-Clean switches in OFF position. 4. Install header by removing all four screws from the electrical box cover. Carefully remove electrical box cover. Place the header (transparency) between the clear and opaque plates (plastic lens). Slip the electrical box cover back on to machine and reinsert the four screws. (See Figure C) 5. Install the standard one piece carb tube by placing it in the hole in the hopper. If your unit is equipped with a two piece smoothie/shake carb tube place the solid piece in the hole in the hopper with the hole facing front to back. Then place the carb tube sleeve over the solid piece, lining up one of the holes with the hole in the solid piece. (Select the larger hole for thickest products). 6. ...
Este manual também é adequado para os modelos :Blenders - 5512E (859.47 kb)