Assessments - 0, GPA: 5
(
)
)
|
Facilidade de uso
Deactivate unnecessary equipment using in Setup Utility. Software Preparation (first time only) The following settings are necessary to prepare the DVD-ROM Drive Pack for use: 4WiñclowslÑ¡T¡i : The following settings are unnecessary.) 1 Add the check mark for [DMA] in [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [CD-ROM] - [MATSHITA DVD-ROM SR-8173] - [Settings], 2 Set [L:] for both [Start drive letter] and [End drive letter] in [Reserved drive letters], then press [OK]. 3 At the [System Properties], press [OK], The display will ask you to restart Windows, select [Yes] to restart. Xnote)- 4Winböwsl95l (with the F1RSTAID CD included): When reinstalling, refer to the above steps 2 - 3 to set the reserved drive letters of the CD-ROM drive. • When booting up from the FIRSTAID FD (for example, to reinstall the operating system), the DVD-ROM Drive does not have to be replaced by the CD-ROM Drive (CF-VCD271). The CD-ROM driver will recognize the DVD-ROM Drive. Using the DVD-ROM Drive Pack in the MS-DOS mode ((WifiPErnaBTi?) : It is unnecessary to read this explanation.) To use the DVD-ROM Drive Pack in the MS-DOS mode, configure the drive following the steps below after performing the above steps l ~ 3. If the steps listed below are performed without completing steps 1-3 above first, the drive will not operate properly. 1 Click the [Start] button then select [Shut Down], 2 Select [Restart in MS-DOS mode] and click [OK]. 3 Open the "CONFIG.SYS" file for editing by issuing the following commands: cd \ ( Enter ) edit config.sys (Enter) 4 Move the cursor to the line containing "( WilmMgRtiB ) ATAPICD.SYS’" and delete the characters "reni" at the beginning of the line. (Deleting "rem" causes the item to become valid.) DEVICEHIGH=C:\WINDOWS\COMMAND\ATAPICD.SYS* /D:MSCD000 (If this line is missing, add it.) *ATAP1CD.SYS (Windowsl98) : OAKCDROM.SYS 5 Pressi Alt 3 +CE) , then( S ) to save the file. Then press C Alt ) + CF"h then to exit the Edit program. 6 Follow the same steps to edit the "AUTOEXEC.BAT” file, edit autoexec.bat ( Enter) 7 Move the cursor to the line containing "MSCDEX.EXE" and delete the characters "rem” at the beginning of the line. (Deleting "rem" causes the item to become valid.) LOADH1GH C:\WINDOWS\COMMAND\MSCDEX.EXE /D:MSCD000 /L:L (If this line is missing, add it.) & Press C Alt) + CT) , then C S ) to save the file. Then press ( Alt) + then ( X ) to exit the Edit program. 9 Restart the computer. Power-saving mode If the DVD-ROM Drive Pack has not been accessed within 120 seconds, the drive motor will automatically shut down to reduce the power consumption. When the DVD-ROM Drive Pack is accessed once again, the power of the drive motor is turned on. However, approximately 30 seconds are required until data is actually read from the disc. Xnote)- • [3,/2 Floppy (A:)] displayed in [My Computer] can be selected, only when you use a floppy disk drive as an external device (<^> page 6). •References to "CD-ROM" in the Setup Utility will not change depending on the computer when the DVD-ROM Drive Pack is installed. • If the vibration of the DVD-ROM drive is excessive, set the CD-ROM/DVD-ROM Drive Speed to [12x](or displayed [Low]) in Setup Utility. ( The display of the item may remain unchanged depending on the computer when the DVD-ROM Drive Pack is installed.) v_:_y Troubleshooting The computer does not recognize the DVD-ROM Drive Pack. • Have you installed the drivers as described in the "Software Preparation" section? • Did you restart the computer after installing the drivers? • Is the DVD-ROM Drive Pack properly mounted in the multimedia pocket? The access lamp (|m^) does not light. Is the disc loaded on the tray correctly? Cannot play disc or read data from it. Is the disc bent, scratched, or dirty? Cannot eject disc. Is the computer powered on? To remove a disc when the computer is powered off, insert a sharp object such as the bent-out tip of a paper clip into the emergency hole. Pushing it completely to the end will free the tray so that it can be pulled out. A blue background appears on the screen with the MPEG image. Did you open the DVD-ROM drive or remove the disc while it was operating? Re-insert the disc and close the DVD-ROM drive. Press C Enter ). The disc tray does not close. Did you touch the eject button when you close the tray? Specifications Item Description Operating voltage range DC 5 V± 0.25 V Drive 4x DVD-ROM Drive/24x CD-ROM Drive max. speed DVD -ROM Data Capacity 4.7 GB(DVD-5), 8.5 GB(DVD-9), 9.4 GB(DVD-IO) Data transfer rate*1 44.32 Mbits/s (5,408 KB/sec) 4x speed (max.) Access Time 280 ms (4x Speed, 1/3 Stroke*2) Supports DVD-5, DVD-9, DVD-10, DVD-R*3 CD -ROM Data Capacity 656 MB Data transfer rate*1 3600 KB/sec 24x speed (max.) Access Time 190 ms (24x Speed, 1/3 Stroke*2) Supports CD-Audio, CD-ROM, CD-R*4, Photo CD, Video CD, Enhanced Music CD, CD-RW*4 Cache memory 512 KB...