Assessments - 3, GPA: 5 ( )

Fabricante : Panasonic Arquivo Tamanho: 773.13 kb Arquivo Nome : CF-VCW722.PDF Língua de Ensino:

Wipe this moisture off with a soft, dry, lint-free cloth before using the disc. • Do not drop, bend, or place heavy objects on top of discs. • Cleaning the disc using a CD cleaner is recommended once every 2 or 3 months. After wiping the disc with a moist, soft cloth, wipe it with a dry cloth. Always wipe from the center toward the edge. Using the Drive Installing/Removing a Drive Refer to the Reference Manual included with your computer on how to install/remove the drive. c ©mTioN Be sure to turn the computer off before installing/removing the drive. Preparations Confirm the following contents in [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [CDROM] - [MATSHITA UJDA***] - [Properties] - [Settings]. Make the settings if they have not yet been made. • Add a check mark for [DMA], • Set both [Start drive letter] and [End drive letter] in [Reserved drive letters] to [L:]. If the product number of your computer is CF-72N3*****, be sure to carry out the following procedure before starting the installation of‘‘Easy CD Creator 4/DirectCD™ 3”. 1 Confirm that the drive letter for the CD-R/RW Drive Pack is "L:'\ 2 Confirm the BaySwap version. (1) Right-click the BaySwap icon Q on the taskbar, then select [About]. (2) Confirm that the version shown fdlowing “BaySwap (TM)” is “1.12.8”, then click [OK], 3 If the version is “1.1.2.8”, update BaySwap with the following steps. (1) Select [Stan] - [Settings] - [Control Panel] - [Add/Remove Programs]. (2) Select [Phoenix BaySwap], then select [Add/Remove], (3) At the [Confirm File Deletion] screen, select [Yes], (4) When the completion screen is displayed, select [OK]. (5) At the confirmation screen, select [OK], (6) Close the [Add/Remove Programs] screen and restart the computer. (7) Set (he Easy CD Creator™ 4/DirectCD™ 3 CD-ROM in the CD-R/RW drive. (8) When the installation screen is displayed, click [XJ. (9) In [Start} - [Run], input “L:\BaySwap\SETUP.EXE'\ then select [OK], Follow the on-screen instructions. (10) In [Start] - [Run], input “C:\UTIL\BAYSWAP2\SETUP.EXE”, then select [OK]. Follow the on-screen instructions. (11) When the setup process completes, remove the CD-ROM and restart the computer. Confirm that [Transfer Mode] is set to [DMA if available] in [Start] - [Settings] - [Control Panel] -[System] - [Hardware] - [Device Manager] - [IDE ATA/ATAPI controllers] - [Secondary IDE Channel] - [Advanced Settings] - [Device 0]. Perform this setting if it has not yet been made. Confirm that [Transfer Mode] is set to [DMA if available] in [start] - [Control Panel] -[Performance and Maintenance] - [System] - [Hardware] - [Device Manager] - [IDE AT A/ ATAP1 controllers] - [Secondary IDE Channel] - [Advanced Settings] - [Device 0]. Perform this setting if it has not yet been made. Setting a Disc 1 Power on your computer 2 Open the disc tray Press the eject button and slowly pull out the tray. /-I note)-—- Before using the drive for the first time, remove the protective sheet from the lens area. The protective sheet inside the drive delays the opening of the drive by about ten sec-onds. This delay is not a problem._ 3 Place a disc Place the disc with the label facing upward in the drive and push down until the center holder clicks. Place a finger on the center holder and lift up on the edge of the disc. 4 Close the disc tray Close the tray without touching the eject button. Xnote)-—- • If the vibration of the drive is excessively high, use the Setup Utility to reduce the drive speed by setting it to [Low], ,4Win3owsi98), In the following cases, the drive speed may not be set to [Low], At a time like this, re-start your computer. • When operation is resumed from the suspend mode • When a drive has been installed while the power was still on • For AutoPlay CDs: • If an AutoPlay CD does not start after the computer resumes from the standby or hibernation mode, we recommend reinserting the CD again after a 15-second wait. • An AutoPlay CD may start during the access of a file. Power-saving Mode If the drive has not been accessed within 30 seconds, the drive motor will automatically shut down to reduce the power consumption. When the drive is accessed once again, the power of the drive motor is turned on. However, approximately 30 seconds are required until data is actually read from the disc. Label side up Using the Drive Using the Drive in the MS-DOS Mode To use the drive in the MS-DOS mode*, configure the drive following the steps below after performing the preparations page 6). If the steps listed below are performed without completing the preparations first, the drive will not operate properly. * In the MS-DOS mode, discs can only be read. 1 Select [Start], then select [Shut Down). Select [Restart in MS-DOS mode], then select [OK]. 3 Open the “CONFIG.SYS” file for editing by issuing the following commands: cd \( Enter) edit config.sys t Enter) 4 Move the cursor to th...

Baixe o seu

Para fazer o download, introduza 2 dígitos :