Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
CAUTION Do not attempt to repair the CD-R/RW drive yourself. Contact your dealer or local SAMSUNG representative for all repairs. Use of controls or adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. WARRANTY Please refer to the Samsung limited warranty statements. http : //samsungelectronics. com. 1 Front View of the Drive Rear View of the Drive 56 English 1234 5 12 34 1 Headphone Connector The audio output connector enables you to plug stereo headphones into the drive. It requires a 3.6mm stereo mini-jack. 2 Volume Control Dial This control dial adjusts the volume for your headphones. You can only use the headphone jack and volume control when you have installed the required software utilities. For example, the Microsoft Windows Media player can be used. 3 Reading/Writing LED When you play a disc.(ORANGE) 4 Emergency Hole If the disc tray does not open when you press the Open/Close button, insert a small, metal rod(an unwound paper clip for example) into this hole to eject the disc. . This function should only be perfomed when the computer is powered OFF. 5 Disc Tray The Disc Tray opens and closes automatically when you press the Open/Close button. When you place a disc in the tray, make sure that the label on the disc is facing upwards. If you are not loading or unloading a disc, the disc tray should remain closed. 6 Open/Close-Button Press open/close key. 2 1 Digital Audio You can connect a sound card or MPEG card which support Digital Audio to your drive using this two-pin connector. 2 Audio Output Connector You can connect a sound card to your drive using this four-pin connector. . This function is not covered in detail in this guide. Refer to the documentation supplied with your sound card. 3 Device Configuration Jumper Usually, this is a pre-set configuration as illustrated below: C S S L M A . Verify that the setting is as illustrated. If it is not, simply remove the jumper and place it in the correct position. 4 Host IDE Interface Connector This input/output interface connector is used to connect the 40-pin flat cable from the IDE interface to the CD-R/RW drive. 5 Power Connector The power connector is a four-conductor male plug. 3 System Before you install the drive, we strongly recommend that your set-up meets the Item Description Type of computer Pentium 133MHz(or higher) with an IDE (For 6X writing, 166MHz recommended) RAM 16MB RAM(or higher) (Recommend 32MB) Hard drive 528MB higher(Transfer Rate 800KB/sec higher, Access Time 20msec Lower) MS-DOS 5.0(or higher) TIP:For MS-DOS, The CD-R/RW drive can only Read a disc without Premaster Software Windows Microsoft ® Windows 95 ® , 98 ® or Windows NT 4.0 ® TIP:For Windows NT ® , we recommend Service Pack3. Installing the CD-R/RW Drive Install the CD-R/RW drive in your computer horizontally, making sure that the Open/Close button is on the right. To install the drive, proceed as follows. 1 1 Turn OFF your computer. Remember to verify the configuration jumper on the rear of the CD-R/RW drive. 2 2 Remove the cover of your PC(main unit of the computer). 3 3 Remove the blank cover panel of the 5.25 inch unit in which the CD-R/RW drive is to be installed. 4 4 Connect the CD-R/RW drive to the IDE interface and power cables located inside your computer. . Connectors are keyed so it is impossible to put them in an incorrect position. Do not force the connectors, if they do not seem to fit. 5 5 Install the CD-R/RW drive into the unit and secure it with mounting screws (recommended standard M3x6). . Depending on your PC model, you may need to attach guide rails to the drive, so that the drive is held firmly in place. On the ground that the guide rails are parts of the computer, if you don’t have these, please purchase separately. If you use screws that are longer than the recommended standard, you may damage the drive. 6 6 Put the cover back on your PC. 4 Installing You can install the device Windows. TIP : You can use the CD-R/RW drive to only read a disc 3.1. * Device Driver is located at [CD] 1 Turn on your computer and wait 2 Insert the bundle CD into CD-R/RW driver. 3 Windows 95/98 user /NT 4.0 When you are in Windows 95/98 or NT, it is not necessary to install Device Driver. Whereas, when you are in Dos Mode of Windows 95/98 or NT, then install as follows. Click on MY COMPUTER icon. Click on the CD-R/RW icon. English 4 Run the CDSETUP program: Windows user Double-click CDSETUP.EXE of [DDRIVER] folder from the Windows File Manager. 5 To.. . Then click... Confirm the installation OK Exit without installing CANCEL Result: If you answer Y(OK), the installation program automatically Creates a SAMSUNG directory on your hard disk Copies the required softwares (mscdex.exe and sscdrom.sys) Modifies the CONFIG.SYS and AUTOEXEC.BAT files When the Setup Completed screen is displayed, remove...