Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
.. . . . . . . . Power Cable . IDE Cable . Audio Cable . Netzkabel . IDE-Kabel . Audiokabel . Cable d’alimentation . Cable IDE . Cable audio . Cavetto di alimentazione . Cavetto di interfaccia IDE . Cavetto di uscita segnale audio . Cable de alimentacion . Cable IDE . Cable de audio . Cabo de alimentacao . Cabo IDE . Cabo de audio ND L SLAVE MASTER 39 40 CS SL MA CS: Cable Select (CSEL) SL: Slave MA: Master CS: Cable Select (CSEL) SL: Slave MA: Master CS: selection de cable (CSEL) SL: esclave MA: maitre CS: Selezione automatica (CSEL) SL: Configurazione Slave MA: Configurazione Master CS: Seleccion de Cable (CSEL) SL: Esclavo MA: Maestro CS: selecao de cabo SL: Slave MA: Master English Features • E-IDE interface • Data transfer rate (DVD-ROM max-16Xspeed: 22,100KB/sec, CD-ROM max-52Xspeed : 7,800KB/sec) • Motorized tray loading system • Designed for internal mounting • Emergency eject support • Read compatible for DVD-R, DVD+R, DVDRW, DVD+RW & DVD-RAM discs • Supports Region playback control Phase II System Requirements* • IBM PC AT or compatible, Pentium-266MHz processor or higher (higher recommended). •A minimum of 64MB memory (higher recommended). •A suitable free standard 5 1/4” internal drive bay. • OS: Windows 2000, XP, Vista. • An existing IDE controller with an available cable connector or a new IDE controller (recommended with IDE PIO Mode 4 capability) that you will need to install. * Please note: Certain software (i.e. particularly those including Video playback) may require a considerably increased specification PC to give acceptable results. While this DVD-ROM drive can read DVD-video discs, decoding them to display on your pc’s monitor requires separate MPEG decoding that is done by separate hardware (either an MPEG decoder card or MPEG decoding done by your video card), or separate software that you install to do MPEG decoding. These items are separate and are not included with this DVD-ROM drive. Location and Function of Controls A Front Panel 1. Disc Tray 2. Drive activity indicator 3. Emergency Eject Hole 4. Stop/Eject Button Rear Panel 1. Digital Audio Output Connector This connector is not supported. 2. Analog Audio Output Connector 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) Interface using a 40-pin flat IDE cable. NOTE : Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Supplied Accessories z zz Owner’s Manual z zz Screw (4 pieces) z zz MPEG-2 software (Power DVD) English Installing the Drive Before installing the drive, turn off the system power. Follow the steps below to install the DVD-ROM drive: B 1. Remove the cover from your computer system. Refer to manual for the computer for details about removing the cover. 2. Adjust the Master/Slave jumpers on the back of the DVD-ROM drive as necessary. Connect the DVD-ROM drive to the IDE ports of your motherboard. In general, the hard drive will connected to the Primary IDE port and its jumper set to Master for booting the operating system. There are two possible alternate connections for DVD-ROM drive installation. C A) When using a Primary IDE port If you need to connect your DVD-ROM drive to the same Primary IDE port, the DVD-ROM drive should be set to Slave position. B) When using a Secondary IDE port You can also connect DVD-ROM drive to the Secondary IDE port and set its jumper to Master. 3. Insert the DVD-ROM drive unit into a free 5.25-inch drive bay. Secure the DVD-ROM drive to the drive bay rails with the mounting screws (supplied). 4. Connect the 4-pin power cable and 40-pin IDE interface cable to the back of the DVDROM drive. Notes: If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type. The red edge of the IDE cable corresponds to pin 1 of the IDE interface on the DVD-ROM drive. Please Note: an IDE cable is not supplied and may be required to be purchased separately. If the computer is using a sound card, the drive is connected to the sound card with an audio cable. This DVD-ROM drive is supplied with a Creative Labs SoundBlaster© compatible audio lead, if this is not suitable for your sound card, it maybe necessary for you to purchase a suitable lead from your retailer. Refer to the manual for the sound card for detailed information regarding connection. 5. When the installation of the drive unit is complete, replace the computer cover. 6. Reconnect the computer power cord and turn on the computer. Device Drivers When using Windows 2000 Pro/XP or Vista, the installation of any software driver or special device is not required. The DOS and Windows 3.1 users can download the DOS Device drivers anytime vi...