Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
RE A D W R IT E R E AD W R IT E 5 NOTE : If two peripheral devices with the same settings are both connected to the Primary or to the Secondary EIDE bus, the host computer may fail to run or may malfunction. Careful attention is necessary. MA: Master SL: Slave CS: Cable Select (CSEL) NOTE : Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. If you use CSEL setting, the MASTER/SLAVE setting will be made automatically, depending on the hardware configuration. For more details refer to the manual of your computer. PC Connection The Super Multi DVD Rewriter connects to the motherboard of the host computer using an IDE interface cable. You may connect the Super Multi DVD Rewriter as a Slave or Master device, depending on your computer. To Install as a Master Drive To install the drive as a Master, the jumper can be left as supplied from the factory. NOTE : A hard disk is normally installed as the Primary Master on the EIDE (ATAPI) interface. Other EIDE peripheral devices such as hard drives and Super Multi DVD Rewriters are then set differently. 6 Name Function Drive set as Master Drive set as Slave MA (Master) SL (Slave) CS (Cable Select) C S S L M A Drive mode set by CSEL on the host IDE interface Primary connector Secondary connector Master drive (Super Multi DVD Rewriter) (Jumper left as Master) Motherboard - OR - DIGITALANALOG INTERFACEPOWER DRCSM SLA GLG39 1 +5+12GND 40 2 AUDIOAUDIO Master drive (Booting hard disk) Secondary connector Master drive (Super Multi DVD Rewriter) (Jumper left as Master) Slave drive (Other IDE drive) DIGITAL ANALOG INTERFACEPOWER D RCSM SL A GLG 39 1 +5+12GND 40 2 AUDIOAUDIO DIGITALANALOG INTERFACEPOWER DRCS M SLA GLG 39 1 +5+12GND 40 2 AUDIOAUDIO Master drive (Booting hard disk) Primary connector To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel to SL. Connecting the Power Connector Connect the power cable from the computer’s power supply to the socket on the drive unit, fitting the connector firmly into the power in connector. If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type. Connecting the Interface Connector Connect the 80-pin IDE cable to the back of the Super Multi DVD Rewriter, making sure the coloured (red) stripe on the IDE cable is connected to pin 1 on the Super Multi DVD Rewriter (Pin 1 is closest to the Power Connector). 7 Slave drive (Super Multi DVD Rewriter) (Jumper set to Slave) Master drive (Booting hard disk) - OR - DIGITAL ANALOG INTERFACEPOWER DRCSM SLA GLG 39 1 +5+12 GND 40 2 AUDIOAUDIO Secondary connector Master drive (Other IDE drive) Slave drive (Super Multi DVD Rewriter) (Jumper set to Slave) DIGITALANALOG INTERFACEPOWER DRCSM SLA GLG 39 1 +5+12GND 40 2 AUDIOAUDIO DIGITALANALOG INTERFACEPOWER DRCSM SLA G LG 39 1 +5+12GND 40 2 AUDIO AUDIO Master drive (Booting hard disk) Primary connector Beveled edge up NOTE : Improper connection may damage the drive and void the warranty. Generally, the power connector can only fit one way. Pin1 Red-edge NOTE : Generally, the IDE connector is keyed and will only fit one way. Connecting the Sound Card If the computer is using a sound card, the drive is connected to the sound card with an audio cable. The supplied analog audio cable fits most sound cards or one can be purchased at a local computer store. Refer to the manual for the sound card for detailed information regarding this connection. Replacing the Computer Cover When the installation of the drive unit is complete, replace the computer cover. L R marking L-R Sound card Device Drivers When using Windows 2000 Professional/XP Home Edition/XP Professional/Vista, no special device driver is required. Your system, upon Power On and bootup after installing and connecting the new Super Multi DVD Rewriter, will recognize and load native software drivers automatically. Please consult the following internet sites: (then choose your country from the list) For Windows 2000/XP Users ¦ In order to ensure normal drive operation, please check the following: • The drive is displayed in Windows 2000/XP : [Control Panel]-[System]-[Hardware]-[Device Manager][ DVD/CD-ROM-drives] • 32-bit is displayed in [Control Panel]-[System]-[Performance] ¦ If the drive is not recognized by your computer, please check the following items. • If an indicator is displayed on the IDE controller in [Control Panel][ System]-[Device Manager]-[Hard Disk Controller], you will need to contact your PC’s manufacturer or the motherboard’s manufacturer and get the appropriate IDE controller driver. ¦ Run Add New Hardware in Control Panel to let PC search again for new device. 8 How to Use the Discs When using CD-ROM discs, CD-R discs, DVD...