Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Insert the batteries observing the polarity (+/-). Failure to properly align the battery polarity can cause personal injury and/or property damage. Do not mix battery types (e.g. alkaline, zinc/carbon, rechargeable batteries) or exhausted and new batteries. Remove exhausted batteries from the device. Remove the batteries when the device will not be used for extended periods of time to prevent damage due to rusted or corroded batteries. To avoid fire and explosion do not recharge normal batteries.Keep batteries away from children and pets. During battery operation of the device, disconnect the AC power cord. Insert 6 batteries type “LR14 / UM-2 / C” batteries into the battery compartment GENERAL OPERATING INSTRUCTIONS RADIO OPERATION 1. Set the FUNCTION selector (2) to the RADIO position. The POWER LED (18) lights up. 2. Set the BAND selector (4) to the desired band: FM ST. (FM stereo), FM (FM mono), AM. 3. Select your station with the TUNING control (6), the adjusted frequency will be shown on the frequency dial (7). 4. Adjust the volume with the VOLUME control (3). 5. To turn off the radio set the FUNCTION selector (2) to the OFF position. The POWER LED (18) turns off. FM Stereo / Mono Stereo: Set the BAND selector (4) to FM ST. The FM ST. LED (14) lights up. Mono: Set the BAND selector (4) to FM. Recommendations For Better Reception FM: Fully extend the telescopic antenna (1) and turn it for better reception. Medium Wave (AM): The device has a built-in AM-antenna; change the position of the device if reception is poor. 20. 21. CD OPERATION Inserting Of A Disc 1. Set the FUNCTION selector (2) to the CD/MP3 position. The POWER LED (18) lights up. 2. Open the door of the CD drive (5) with the grip (8) at the right side of the lid. The display shows “OP“. 3. Insert a CD with the cover side faced up. 4. Close the CD-door (5) manually. Note: If a not supported CD (VCD, DVD) is inserted, the display shows “no“. Taking Out Of A Disc 1. Make sure the device is in stop mode (STOP button (13)). 2. Open the door of the CD drive (5) with the grip (8) at the right side of the lid. The display shows “OP“. 3. Remove carefully the CD upwards without touching the surface. 4. Close the CD-door (5) manually. 5. Store the removed CD in its cover. CD / MP3 Disc Playback 1. Insert a CD (see section “INSERTING OF A DISC“). 2. During the reading of a CD “- - -” flashes on the display and afterwards the total number of tracks will be shown. 1. Audio CD: total number of tracks. 2. MP3 CD: total number of tracks and “MP3“ is shown. 3. The playback of the first track starts automatically. 6. Adjust the volume with the VOLUME control (3). 7. Press PLAY / PAUSE (19) to pause the playback. The symbol “ ” flashes on the display. To resume the playback from the same position press PLAY / PAUSE (19) again. 8. Press STOP (13) to cancel the playback. 9. Set the FUNCTION selector (2) to the OFF position to turn off the CD player. The POWER LED (18) turns off. Selection Of A Different Track (SKIP in the stop mode and during playback) 1. Press SKIP + (16) or SKIP - (17) until the desired track number is displayed. 2. Shortly press SKIP - (17) to return to the beginning of the current track. 3. Press SKIP - (17) again to skip one track back at a time. 4. Press SKIP + (16) to skip to the next track at a time. Selection Of A Different Album (only MP3, in the stop mode and during playback) 1. Press ALBUM (12) once. On the display “ALBUM“ and the current album number flashes. 2. Repeatedly press ALBUM (12) until the display shows the desired album number. 3. Press PLAY / PAUSE (19) to start the playback of the first track in the selected album. Search For A Certain Position During Playback Press and hold SKIP + (16) or SKIP - (17) to search for the desired position within the track. Normal playback continues when the button is released. In search mode the volume is reduced. Program Playback Up to 99 tracks can be programmed in a specified playback sequence. 1. Before programming press STOP (13). 2. Invoke the program mode by pressing PROGAM (11). “P01“ and “PROG“ are flashing on the display. 3. Select the desired track number with SKIP + (16) or SKIP - (17). (With the ALBUM button (12) the album/folder can be selected). 4. Press PROGAM (11) again to confirm. 5. Repeat steps 3 and 4 to program further tracks. 6. After all desired tracks are programmed, press PLAY / PAUSE (19) to start the programmed sequence. On the display “PROG“ is shown. 7. Press STOP (13) once to finish the program playback and add further tracks beginning from the next free program number (see 5.). 8. Cancel the program playback and delete the program memory by pressing STOP (13) twice. Notes: After entering more than 99 programmed tracks the display shows “FUL“. Turning off the player deletes the program memory. Repeat Repeat One Track 1. In the stop mode or playback mode press MODE (15) once. 2. The display shows “REP“. In the stop mode press now PLAY / PAUSE (19) for playback...