Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
indication will return to “ ”. 4. Repeat steps 2 and 3, until all the desired tracks are programmed ( up to 20 tracks). 5. Press “ ” button, “ PROG ” stops flashing and program playing starts. NOTES: • Repeat play and intro play can be performed during program play. But random play is inactive. • The program is erased when the disc compartment is opened or the auto power off function turns the power off. • If the program mode is exited by means of the “ ” key, all the programs would still remain in memory. PROGRAM EDITION To add: To add additional tracks to your selection during program playback, press “ ” button first and then press “ PROG ” button repeatedly until “ ” flashes in the display window. Repeat the above step 2 and 3 to store additional tracks. To check: Press “ PROG ” button during programming before you press “ ” button. Each time “ PROG ” button is pressed the track number appears in the display window. To change: When checking press either skip button to alter the track number for the program currently displayed. Press “ PROG ” button to register the newly selected track into memory. To delete: When open the CD door including that program will be cancelled. TROUBLE SHOOTING GUIDE Should any problem persist after you have made the following checks, consult your nearest service facility. DISC PLAY DOES NOT START: • The disc is inserted upside down or incorrectly. Insert the disc correctly with the label surface up • Dusty or defective disc • Dirty or dusty lens • The disc compartment lid is not closed • Moisture condensation-> leave the unit in a warm place until the moisture evaporates • The AC power adaptor is not plugged into the wall outlet • The unit is not placed on a level surface • Weak batteries NO SOUND FROM THE HEADSETS: • The headphones / earphones plug is not firmly connected to the “ PHONES ” jack. • Adjust the volume control • Dirty plug SKIPPING OF SOUND: • Dirty or defective disc • Dirty lens • Strong vibration WHEN USING WITH BATTERIES THE BATTERY LIFE IS SHORT: • Use alkaline batteries and not manganese batteries. DISPLAY WINDOW SHOWS “ ” ERROR MESSAGE AND THE UNIT CANNOT BE OPERATED: • No disc, dirty or scratched disc. The unit will return to power off after approx. 30 seconds, or reset the player by pressing “ ” button once and then insert a disc to start playing. SPECIFICATIONS SKIP PROTECTION SYSTEMVARIOUS PLAYING MODES During playback, every time the “ MODE ” button is pressed, the playing mode would be changed to the next one as follows: IN NORMAL PLAYING MODE: NORMAL PLAY -> ( ) REPEAT ONE -> ( ) REPEAT ALL -> INTRO -> SHUFFLE NORMAL PLAY--Playing the whole disc The CD is played once from the beginning to the end. REPEAT PLAYBACK--Repeat one and repeat all • To repeat the same track Press “ MODE ” button during play until “ ” appears in the display window. Select desired track to be played only once by pressing “ ” or “ ” button. • To repeat whole disc Press “ MODE ” button during play until “ ” appears in the display. The whole disc will be played repeatedly. INTRO PLAY--Playing the first about ten seconds of all the tracks 1. Press “ MODE ” button during play until “ INTRO ” flashes in the display. 2. Press “ ” button to begin “ INTRO ” play. (Play each track for approx. 10 seconds.) 3. Pressing “ ” button again will cease “ INTRO ” play and continue playback in the “ NORMAL ” play mode. NOTE: “ INTRO ” play always starts from the first track. The SKIP PROTECTION System incorporates a special electronic circuit that prevents sound from skipping when the unit is subjected to shocks and vibration during play. When you start playback, the SKIP PROTECTION System turns on and “ ” indicator appears in the display to prevent sound skipping. When the unit receives a physical shock which prevents the laser pick-up from "reading" the CD, this system immediately starts playing the sound stored in its memory and continues until the laser pick-up recovers. If the unit is subjected to continuous shocks and all the data stored in memory is used up the sound will skip. If the vibration stops then the data memory will be restored. If continuous vibration is applied when the data memory is empty, an error message “ ” will be displayed. To reset the CD player press “ ” once. MAINTENANCE CLEANING THE UNIT Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth. CLEANING A CD If the CD skips or will not play, the disc may need to be cleaned. Before playing, wipe the disc from the centre out with a cleaning cloth. After playing, store the disc in its case. HANDLING THE DISC Only touch the CD on the edge to avoid leaving finger prints on its surface. Do not stick paper or tape or write anything on the surface. GENERAL OUTPUT (at 1KHz 0dB level): Headphones / earphones (stereo mini-jack) 15 mW+15mW at 16 Ohms to 32 Ohms POWER REQUIREMENTS: 3V --- (2 x AA / LR6 / MN 1500) alkaline batteries,or DC IN 6V, 350mA power adaptor Polarity of plug OPERATING VOLTAGE: U...
Este manual também é adequado para os modelos :CD-players - DM8100_9H_wRW (502.38 kb)