Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
‘ ‘ ’ ’ indicator will light up in the display window and playback begins automatically. Labeled side up n NEVER Insert 3-inch CD’s. This unit is designed for playback of standard 5-inch CD’s only. Do not attempt to use 3-inch CD singles in this unit, either with or without an adaptor, as damage to the player and/or disc may occur. Tip/FYI During playback of a CD, the pie-shaped indicator spins. Listening to a disc Press the CD to select the CD mode. Playback begins automatically. Pausing Playback Press the 6/ . To resume playback, press the 6/ again. Stopping Playback Press the AM or FM to select the radio reception. Ejecting Discs Press the to eject the disc. Note The unit will turn-on automatically when a CD is inserted if the ignition switch is ‘‘ON’ ’. Playing a CD in various modes Track Search Press the or during CD mode. Track numbers appear in the display window. : Playback starts from the beginning of the next track. : Playback starts from the beginning of the current track. Press again to play the previous track. Cue / Review Press and hold the or during CD mode. Release when you have found the desired point. : To search forward. : To search backward. Scan Play Press the during CD mode. The ‘ ‘SCAN’ ’ indicator appears in the display window. This will play the first 10 seconds of all the on the disc. Press the again to cancel this feature. Repeat Play Press the 5/ RPT during CD mode. The ‘ ‘RPT’ ’ indicator appears in the display window and the current track is played repeatedly. Press the 5/ RPT again to cancel this feature. MIX Play Press the 4/MIX during CD mode. All the tracks on the current disc are played in random order. Press the 4/MIX again to cancel this feature. ENGLISHE Installations ENGLISHE Supplied Mounting Sleeve Bushing, Locking Mounting Strap Release Screw Screw and Screws Keys Precautions • Be sure to remove/detach the front panel before you start installing the unit. • Choose the mounting location carefully so that the unit will not interfere with the normal driving operations of the driver. • Use only the supplied mounting hardware for a safe and secure installation. • Handle the sleeve carefully to avoid injuring your fingers. • When mounting the unit in a car, keep the unit as level as possible. If the unit must be mounted at an angle, due to the design of the vehicle, make sure that the unit does not tilt upward by more than 30°. Mounting Example Installation in the dashboard. 1. Install the sleeve in the dashboard. 2. Select and bend the appropriate tabs to hold the sleeve firmly in place. Mounting Strap Use * 3. Attaching the Mounting Strap to the underside of the dash board, using screw. Attach the back of the unit to the Mounting Strap using the support stem bolt and hardware. Fire wall Removal trim ring (Supplied) Bushing Use * 3. As shown in the figure below, securely fasten the screw, which has been inserted into the bushing, at the rear of the unit. Removal trim ring Fire wall (Supplied) The distance to the fire wall varies due to the type of the car. Be sure to secure the unit by properly inserting the bushing. Caution Insufficient fastening of the screw may cause some CD’s to skip. * Warning Failure to properly install the Mounting Strap or rear support Bushing is a major cause of CD skipping. Without these securing devices, the chassis of the CD receiver is able to move up & down whenever the road has imperfections and CD skipping results. Note Some Japanese/Asian vehicles such as TOYOTA & NISSAN do not require use of the sleeve and trim ring assembly. To secure the replacement radio use the O.E.M. brackets and mounting screws. These brackets will align with the threaded screw holes found on each side of the new radio. Connections Warning • To prevent short circuit, remove the key from the ignition and disconnect the battery’s (-) terminal. • This unit is designed for negative ground 12 V DC operation only. You can not use it for 24 V or other types of car batteries. Connection procedure Caution • DO NOT connect any speaker wires to the metal body or chassis of the vehicle. • DO NOT connect the speaker common (-) wires to each other. • Connect each speaker wire directly to each speaker terminal. • All speaker common (-) wires must remain floating. i.e. No Common Connections or connections to vehicle grd . • Connect each pair of speaker leads only to a single speaker (or speaker system) that has an impedance of least 4 ohms, as well as 40-watt power-handling capability. • Do not connect speaker leads to any inputs on external amplifiers. This will cause damage to the internal amplifier of this unit. 1 Make sure the car’s ignition key has been removed. 2 Disconnect the negative (-) terminal of the car’s battery. 3 Connect the wiring harness wires in the following order : Ground wire (Black), +12V Constant Power Supply (Yellow), +12V Accessory/Switched (Red) and Power Antenna/Amplifier Turn On (Blue), and tape each so they do not come in contact with each other. 4 C...
Este manual também é adequado para os modelos :CD-players - RPD 540 (809.69 kb)