Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
LOOP: After a cue point is programmed, pressing LOOP (11) while in the PLAY mode (CUE LED blinks yellow) repeats the section between the cue point and the point where the LOOP button was pressed. Press EXIT/RETURN or PAUSE/PLAY to EXIT Loop repeat. EXIT/RETURN: Press loop EXIT/RETURN (12) to return to the beginning of the previously saved loop from normal play. SINGLE-AUTO CUE/CONTINUOUS: Pressing SINGLE-AUTO CUE/ CONTINUOUS (5) activates the AUTO CUE FUNCTION. The Auto Cue causes the CD to pause at the recorded beginning of the next track and allows you to segue into the next song with no “dead” air. Pressing SINGLE-AUTO CUE/CONTINUOUS a second time will activate the CONTINUOUS function. This causes the CD to repeat play continuously until SINGLE-AUTO CUE/CONTINUOUS is pressed a third time to deactivate the CONTINUOUS function. PITCH CONTROL: Pushing PITCH CONTROL (17) activates the PITCH section of the unit (PITCH LED glows red). The pitch of the CD will change according to the position of the PITCH SLIDE (14). PITCH BEND BUTTONS : Pushing the PITCH BEND (18) buttons will automatically raise the pitch up to +4% or lower the pitch down to -4% from the existing setting. Releasing the buttons returns pitch to the original setting. Use this function to match the pitch bend when mixing from one song to another. DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD DRIVE, or other such items which accept digital signals to the BNC (20) output connector on the rear panel of your CDX allows you to record a digital signal from CD. OPERATING INSTRUCTIONS 1. Make sure that the VOLTAGE SELECTOR (19) switch, found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER (1) switch. The unit is ON. Pushing POWER a second time turns the unit OFF. 2. Press OPEN/CLOSE (3) and place a CD in the DISC TRAY (2). Press OPEN/CLOSE again. The tray will close. Page 4 3. Push TRACK SKIP (13) to select the track you wish to play. I IIIIIN CONTINUOUS MODE OR DURING NORMAL PLA N CONTINUOUS MODE OR DURING NORMAL PLAN CONTINUOUS MODE OR DURING NORMAL PLAN CONTINUOUS MODE OR DURING NORMAL PLAN CONTINUOUS MODE OR DURING NORMAL PLAN CONTINUOUS MODE OR DURING NORMAL PLAY YYYYY: ::::: 4. Press PLAY/PAUSE (16) and the unit will instantly play. FLY CUE & CUE INSTRUCTIONS The FLY CUE function lets you set cues “on the fly” with the press of a button. Press FLY CUE when the disc reaches the musical location you wish to make your cue or start point. The cue point is now programmed. Press CUE to return to the cue point. Press PLAY/PAUSE and the unit instantly starts from this pre-programmed spot. AND/OR 1. To pre-program a cue point (the spot on a CD at which you want play to start) select the proper track and push PLAY/PAUSE so the unit enters the PLAY mode (PLAY/PAUSE LED glows green). When the CD reaches the approximate musical spot you wish to make your cue, push PLAY/PAUSE so the unit enters the PAUSE mode (PLAY/PAUSE LED blinks). Move the SEARCH JOG WHEEL forward or in reverse until the precise spot at which you want CD play to begin is located. Push PLAY/PAUSE. The cue point is now programmed. Press CUE to return to this pre-programmed cue point at any time. Push PLAY/PAUSE and the unit will instantly play from the pre-selected spot. 2. To fine tune your pre-programmed cue point, push PLAY/PAUSE so the unit enters the PLAY mode. Push the CUE button and the CD will return to the cue point you programmed in step #1 and begin play from that point. If you decide this cue or starting point is okay, leave the unit alone until you are ready to play. 3. If, however, the selected spot is not exactly where you want it, push the CUE button while the CD is playing and the disc will return to the pre-programmed cue point. Locate the exact spot on the CD at which you want play to start by turning the SEARCH JOG WHEEL. Push PLAY/PAUSE to preprogram this new cue point. Press the CUE button to pause play at the new cue point. Push PLAY/PAUSE at any time and the unit will play from the pre-selected spot. TROUBLESHOOTING • If a disk will not play, check to see that it was loaded correctly (label side up) and that the CD unit is on a flat, level, stable surface. Check disc for dirt, scratches, spills, etc. • If the disc spins but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver. • If the CD skips, check it for dirt, oil or scratches. Do not assume that the CD player or laser is defective. Many CDs are recorded “out of spec” and skip on most or all CD players. Before sending the unit to an authorized Gemini service technician, insert a disc that plays properly in another unit. CDX-602 ROBO START INSTRUCTIONS IN SINGLE-A IN SINGLE-AIN SINGLE-AIN SINGLE-AIN SINGLE-AIN SINGLE-AUT UTUTUTUTUTO CUE MODE O CUE MODEO CUE MODEO CUE MODEO CUE MODEO CUE MODE: Use ROBO START (25) in SINGLE-AUTO CUE MODE (5) to alternate play between the CDX-602’s two CD players (one track from one side, th...
Este manual também é adequado para os modelos :CD-players - CDX-601 (256.26 kb)