Assessments - 3, GPA: 4
(
)
)
|
Fotos e especificações Gemini CDJ-02 |
Facilidade de uso
Excessive force may cause damage. If the switch does not move smoothly, contact a qualified technician. CONNECTIONS: 1. Plug one end of a set of RCA connectors into each of the LINE OUTPUT (2) jacks. 2. Plug the other end of the RCA connectors into any available line level input jacks on your mixer. If you are playing the CDJ-02 through a receiver, you can plug the RCA connectors into the CD or AUX input jacks on your receiver. If there are no CD or AUX inputs, use any line level (not phono) inputs. 3. Connect any type of device that will accept a DIGITAL signal, such as DAT, MD, HARD DRIVE, ETC to the COAXIAL (3) INPUTS on the rear panel of the transport to record a DIGITAL signal. 4. Connect the power plug into the POWER JACK (4) for power. FUNCTION DESCRIPTIONS: POWER SWITCH: After making sure that the VOLTAGE SELECTOR SLIDE (1), found on the rear panel, is properly set, plug the unit in and press the POWER (5) switch. The unit will turn on. Pressing the POWER (5) switch a second time will turn the unit off. DISC IN SLOT: The DISC IN SLOT (6) is where the CD is held. When a disc is in the slot the blue LED bar will be illuminated. STOP/EJECT: Press STOP/EJECT (7) once to stop, twice to eject, and hold down to eject the CD. CUE: With the unit in the play mode, and after memorizing the cue point, pressing the CUE (8) button will cause the CD player to enter the pause mode at the memorized cue point. Holding down the cue button changes the cue function to preview (allowing you to hear the music play from the cue point) and releasing the cue button returns you to the preset cue point. If a cue point is not memorized, pressing the CUE (8) button will cause the unit to return to the beginning of that track. PLAY/PAUSE HI-' Each press of the PLAY/PAUSE (9) button causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. DISPLAY: The DISPLAY (10) shows the track numbers, play mode, pause mode, and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. PLAYBACK DISPLAY: The PLAYBACK DISPLAY (11) displays the time remaining to play and flashes slowly when the track has 30 seconds left. The PLAYBACK DISPLAY (11) flashes quickly when the track has 15 seconds left. TRACK SKIP MM: The TRACK SKIP (12) buttons let you select the track to play. SEARCH BUTTONS 4-4 ►>: The SEARCH (13) buttons are used to move foward or reverse while in play mode. The SEARCH (13) buttons are also used to accurately position the disc at the point where you wish the track to start playing. This position on the track is memorized as the cue point. See the CUE INSTRUCTIONS section for more information. SINGLE: Pressing the SINGLE (14) button activates the AUTO-CUE function. The AUTO-CUE function causes the unit to pause at the beginning of music of the following track and allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track). Pressing the SINGLE (14) button a second time activates the CONTINUOUS function causing the unit to play continuously (after the last track, the unit will return to the first track of the disc and continue to play). Pressing the SINGLE (14) button a third time deactivates the CONTINUOUS function. TIME: The TIME (15) button switches the time display between the three available choices listed under DISPLAY. LOOP IN: Pressing the LOOP IN (16) button while a track is playing will set a loop point. LOOP OUT: After a loop point is memorized, pressing LOOP OUT (17) in play mode will repeat the section between the first loop point and a second loop point when the LOOP OUT (17) button was pressed. Press LOOP OUT (17) again or pause play to exit the repeating play. RELOOP: Press for repeated loop play (stutter) from the first loop point or to reloop a previously set loop. The RELOOP (18) function automatically returns the music to the loop point and will play the loop until it is released with the LOOP OUT (17) button. CD starts instant play from the previously set cue points. PITCH SELECT: Pressing the PITCH SELECT (19) buttons enable you to select pitch levels ranging from 4%, 8%, & 16%. Press the two buttons labeled PITCH OFF together to turn OFF the pitch control. (4) PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (20) will automatically raise the pitch up to +4% or lower the pitch down to -4% from the existing pitch setting. Releasing the buttons will return the pitch to the original pitch setting. You can use this function to match the pitch bend when mixing from one song to another. PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (21) up or down will lower or raise the pitch percentage. JOG WHEEL: Use the JOG WHEEL (22) to make fine adjustments in pause mode for cueing or bending the pitch for precise synchronization in play mode. PGM (PROGRAM): Use the PGM...