Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. (consult a qualified technician if you are unsure) • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place. TYPICAL FRONT-LOAD DIN MOUNTING METHOD MXD45 INSTALLATION Wiring Diagram FUSE When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The MXD45 uses one 5 amp AGC fuse (Battery) located in-line. * CAUTION - Do not attach any speaker leads to ground as severe damage will occur. MXD45 OPERATION Control Locations 1716151413122010111918123465798 12345678910 Release Power Volume Up/Down Audio Play/Pause Bass Boost/Mono/Stereo Tune/Track Up/Down Band Eject Mute 11121314151617181920 Auto Store/Preset Scan Display Scan Local/Distance Preset 6 Preset 5 Preset 4 Preset 3/CD Intro Preset 2/CD Random Preset 1/CD Repeat MXD45 OPERATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Semi-permanent Faceplate Installation Remove trim ring and install supplied #1 x 7/32” Phillips head screw through left side of mounting frame into faceplate. Power On/Off Press PWR or any other button (except eject) to turn the unit on. Inserting a disc will turn the unit on automatically. Press PWR to turn the unit off. CD Mode Insert a CD or press l/ II to begin or resume playback. Tuner Mode Press PWR or BAND to begin or resume tuner operation. Bass Boost Press BASS to activate and deactivate bass boost curve. Activating this feature will enhance the bass frequencies when listening to music at all volumes. Volume Adjust volume using VOL t / VOL s (00-46). Mute Press MUTE to silence the audio. “MUTE” will appear in the display. Press MUTE again to cancel. Display Press DISP to display the clock. The radio frequency (tuner mode) or CD track/elapsed time (CD player mode) show by default. Set the Clock Press DISP to display the clock, then release. Press and hold DISP for 2 seconds, the clock will begin to flash. Press TUNE << to adjust the hours and TUNE >> to adjust the minutes. Clock settings will be saved after 5 seconds. 12/24-hour Clock The clock will display 12-hour AM/PM time in U.S. frequency spacing mode (PM 10:00). In European frequency spacing mode, the clock will display 24-hour time (22:00). MXD45 OPERATION General Operation Reset Audio Bass Treble Balance Fader Press and hold for more than 2 seconds to RESET the unit upon initial installation. The RESET button is located behind the faceplate. Refer to page 2 for details. Press AUD to select between Volume (default), Bass, Treble, Balance & Fader. VOLUME BASS TREBLE BALANCE FADER Press AUD until BA appears Press VOL t or s to adjust ( -7 minimum / 7 maximum) Press AUD until TR appears Press VOL t or s to adjust ( -7 minimum / 7 maximum) Press AUD until B appears Press VOL t (LEFT) or s (RIGHT) to adjust (BL 15/BR 15) BAL 00 represents equal balance. Press AUD until F appears Press VOL t (FRONT) or s (REAR) to adjust (FF 15/FR 15) F 00 represents equal balance. MXD45 OPERATION Tuner Operation Seek Tuning Press TUNE << or >> momentarily to seek the next strong station. Manual Tuning Press TUNE << or >> for more than 2 seconds, then release. “MANU” will momentarily appear in the display. Press TUNE << or >> momentarily to move radio frequency up or down one step at a time. Press and hold to advance quickly. If tuning is not adjusted for 5 seconds, the unit will return to seek tuning mode (default). “AUTO” will momentarily appear in the display. Scan Tuning Press SCAN to preview strong stations on the current band, pausing for 5 seconds at each. Press SCAN again to cancel. FM Local/Distance Press LOC to activate local tuning for strong FM station reception only. Press LOC again to cancel and resume distance tuning (default). FM Mono/Stereo Press MO/ST for more than 2 seconds during FM tuner operation to select mono or stereo (default) reception of the broadcast signal. Band Press BAND to select between FM1, FM2, FM3 and AM1, AM2 bands. Frequency Spacing Press and hold BAND then press TUNE << to select European frequency spacing. Press and hold BAND then press TUNE >> to select U.S. frequency spacing (default). Anytime frequency spacing is changed, all station presets are erased. Storing and Recalling Station Presets Up to 18 FM stations and 12 AM stations can be stored. To store a station, select th...