Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
/ §. • Normal playback resumes. Note : When searching within a final track and you reach the end of the last track, the CD goes to stop mode. Programming track numbers You may store up to 32 tracks in the desired sequence. If you like, store any track more than once. 1 In the stop position, press PROG to activate programming. . Display shows 1 indicating the start of the program. prog flashes. (See 5) 2 Press . or § to select your desired track number. 3 Press PROG to store the desired track number. . Display shows your desired track number briefly followed by a number, 2 (up to 32 in sequence) indicating the next program location available. (See 6) 4 Repeat steps 2 to 3 to select and store all desired tracks in this way. . Fu indicates the program memory is full (when you have stored tracks on all 32 program locations). 5 To play your program, press PLAY/PAUSE 2;. To review a program • In the stop position, press PROG repeatedly to see your stored track numbers. Erasing a program You can erase the contents of the memory by: – selecting TUNER or TAPE/POWER OFF sound source; – opening the CD door; .Display: prog disappears. Cassette playback 1 Adjust the source selector to TAPE/POWER OFF. 2 Press 9/ to open the cassette holder and insert a cassette and close the deck. 3 Press 2 to start playback. 4 To pause playback press ;.To resume, press the key again. 5 By pressing 5 or 6 , fast winding of the tape is possible in both directions.To stop fast winding, press 9/ 6 To stop the tape, press 9/. The keys are automatically released at the end of a tape and the set switched off (unless PAUSE mode ; has been activated.) General information on recording • Recording is permissible insofar as copyright or. other rights of third parties are not infringed. • For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken.This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. • The best recording level is set automatically. Altering the VOLUME will not affect the recording. • To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape. Synchro Start CD recording 1 Select CD source. 2 Insert a CD and if desired, program track numbers. 3 Press 9/ to open the cassette holder. Insert a blank tape and close the deck. 4 Press 0 to start recording. . Playing of the CD program starts automatically from the beginning of the program. It is not necessary to start the CD player separately. 5 For brief interruptions press ;.To resume recording, press ; again. 6 To stop recording, press 9/. CD Player CD Player Cassette Recorder Recording from the Radio 1 Adjust the source selector to TUNER to select your desired waveband. 2 Tune to the desired radio station (see Tuner reception). 3 Press 9/ to open the cassette holder. Insert a blank tape and close the deck. 4 Press 0 to start recording. 5 For brief interruptions press ;.To resume recording, press ; again. 6 To stop recording, press 9/. Precautions & General Maintenance (See 7) • Place the set on a hard and flat surface so that the system does not tilt. • Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. • Do not cover the set. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up. • The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. • To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. Tape deck maintenance (See 7) To ensure quality recording and playback of the tape deck, clean parts A,B and C as shown, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1 Open the cassette holder by pressing 9/. 2 Press 2 and clean the roller C. 3 Press ; and clean the heads A, and the capstan B. 4 After cleaning, press 9. . Cleaning of the heads can also be done by playing a cleaning cassette through once. CD player and CD handling (See 7) • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always close the CD-tape door to avoid dust on the lens. • To clean the CD, wipe in a straight line from the center towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. Problem – Possible cause • Remedy No sound /power – Volume not adjus...