Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
• Remote control ( AZ1325 models only): optionally, press PRESET + ,- to select your preset station. CD PLAYER Playing a CD This CD player plays Audio Discs including Recordables and CD-Rewritables. 1. Adjust the POWER slider to CD. 2. Open the CD Door. ™ OPEN is displayed. 3. Insert a CD with the printed side facing up and close the door. ™ nocd if no CD inserted/ CD dirty, incorrectly inserted or damaged. ™ nFcd if you have inserted a non-finalized CDR( W). 4. Press 2; to start playback. 5. To pause playback press 2; . Press 2; again to resume play. ™ Display: flashes during pause. 6. To stop CD playback, press the 9 button. Note : CD play will also stop when: - the CD door is opened - the CD has reached the end - you select MW / FM function. Selecting a different track •Press SEARCH . or § once or repeatedly to select your track. •In the pause / stop position, press. 2; to start playback. CD PLAYER Finding a passage within a track 1. Press and hold SEARCH . or § . – The CD is played at high speed and low volume. 2. When you recognize the passage you want, release . or § to resume normal playback. Note : During a CD program or if SHUFFLE/ REPEAT active, searching is only possible within a track. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback, and combine the modes with PROG. ( See 4) (SHUFFLE) - tracks of the entire CD/ program are played in random order (SHUFFLE REPEAT ALL) - to repeat the entire CD/ program continuously in random order (REPEAT ALL) - repeats the entire CD/ program (REPEAT) - plays the current track continuously 1. To select play mode, press MODE once or more. 2. Press 2; to start playback if in the stop position. 3. To select normal playback, press MODE repeatedly until the various modes are no longer displayed. – You can also press the 9 button to cancel your play mode. CD PLAYER Programming track numbers In the stop position, select and store your the desired sequence. Up to 20 tracks can in the memory. 1. Press SEARCH . or § on the set to select your desired track number. 2. Press PROG. ™ Display: PROG, Prog briefly and your selected track number. ( See 5) ™ If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. ™ Display: FULL if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence. Erasing a program You can erase the program by either: •pressing 9 twice ™ CLr is displayed briefly and PROG disappears. •You select MW / FM function. • Open the CD door. SAFETY & MAINTENANCE SAFETY & MAINTENANCE INFORMATION (See 7) • Don't expose the set, batteries, CDs to humidity, rain, sand or excessive heat. •Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. •Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. • The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. CD player and CD handling •If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. •Always close the CD door to avoid dust on the lens. •To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. TROUBLESHOOTING If a fault occurs, first check the points If you are unable to remedy a problem WARNING: Do not open the set as there is a circumstances should you try to repair invalidate the guarantee. No sound /power – Volume not adjusted • Adjust the VOLUME – Mains lead not securely connected • Connect the AC mains lead properly – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly Severe radio hum or noise – Electrical interference: set too close to TV, VCR or computer • Move the set to increase the distance Poor radio reception – Weak radio signal • FM: Adjust the FM telescopic aerial nocd indication – CD badly scratched or dirty • Replace/ clean CD, see Maintenance – Laser lens steamed up •Wait until lens has cleared nFcd indication – CD-R(W) is blank/ not finalized • Use a finalized CD-R(W) dAtA indication – CD contains non-audio files • Press SEARCH . or § once or more to skip to a CD audio track, instead of the data file The CD skips tracks – CD damaged or dirty • Replace or clean CD – SHUFFLE or PROG is active • Switch of...