Log:
Assessments - 0, GPA: 0 ( )

Instruções de Operação Philips, Modelo AZ1574/00

Fabricante : Philips
Arquivo Tamanho: 7.96 mb
Arquivo Nome :
Língua de Ensino: itenesfrdenl
Ir para baixar



Facilidade de uso


• To clean the set, use a soft, slightly dampened chamois leather. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing. Safety information • Place the set on a hard and flat surface so that the system does not tilt. Make sure there is adequate ventilation to prevent the system from overheating. • The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. CD REWRITABL E C D S Y N C R O S T R A T R A Z 1 5 7 4 C D R A D IO C A S S E T T E R E C O R D E RSTOP PLAY•PAUSE V OLUME CD RE C D S Y A Z 1 5 7 4 C D R A D IO C A S S E T T E R E C O R D E RSTOP PLAY•PAUSE P R O SOUNDCOBAT L O V OLUMEV O L 6 DIGITAL TUNER Tuning to radio stations 1. Select TUNER source. ™ is displayed briefly and then the radio station frequency is shown. 2. Press BAND once or more to select your waveband. 3. Press SEARCH . or § (on the remote control, TUNING . or §) and release when the frequency in the display starts running. AZ1575 CDRADIOCASSETTERECORDER OPESTOP PLAY•PAUSE TUNER PRESET PROG SHUFFLE REPEAT SEARCH BAND SOUND CONTROL CENTER REMOTESENSOR FM AM BATLOW LW PROGSTEREOSHUFFLE • • VOL ™ The tuner automatically tunes to a station of sufficient reception. Display shows during automatic tuning. ™If an FM station is received in stereo, STEREO is shown. 4. Repeat step 3 if necessary until you find the desired station. • To tune to a weak station, press SEARCH . or § briefly and repeatedly until you have found optimal reception. To improve radio reception: • For FM, pull out the telescopic aerial. Incline and turn the aerial. Reduce its length if the signal is too strong (very close to a transmitter). • For MW (AM or LW), the set is provided with a built-in aerial so the telescopic aerial is not needed. Direct the aerial by turning the whole set. Programming radio stations You can store up to a total of 30 radio stations in the memory. 1. Tune to your desired station (see Tuning to radio stations). 2. Press PROG to activate programming. ™Display: PROG flashes. 3. Press PRESET 3 or 4 once or more to allocate a number from 1 to 30 to this station. 4. Press PROG again to confirm the setting. ™Display: PROG disappears, the preset number and the frequency of the preset station are shown. 5. Repeat the above four steps to store other stations. • You can overwrite a preset station by storing another frequency in its place. Tuning to preset stations Press TUNER PRESET 4 or 3 until the desired preset station is displayed. AZ1575 CDRADIOCASSETTERECORDER OPESTOP PLAY•PAUSE TUNER PRESET PROG SHUFFLE REPEAT SEARCH BAND SOUND CONTROL CENTER REMOTESENSOR FM AM BATLOW LW PROG SHUFFLE • • VOL English 7 DIGITAL TUNER CD PLAYER English Changing tuning grid (some versions only) In North and South America the frequency step between adjacent channels in the AM (MW) and FM band are 10 KHz and 100 KHz respectively. In the rest of the world this step is 9 KHz and 50 KHz. Usually the frequency step has been preset in the factory for your area. 1. Check that the set is in the TAPE/OFF position and switched off. 2. To select 9KHz: Simultaneously, press PROG and REPEAT on the set. 3. Switch the set on to TUNER and then release the controls. • To select 10KHz: Repeat steps 1-3 but in step 2, simultaneously, press PROG and SEARCH § on the set. – When you tune to radio stations, the display shows tuning in either steps of 9 or 10. – All preset stations will be affected and you may need reprogramme the preset stations. Playing a CD 1. Select CD source. 2. Press OPEN•CLOSE to open the CD door. ™Display: when you open the CD door. 3. Insert a CD or CD-R(W) with the printed side facing up and press OPEN•CLOSE to close the CD door. ™Display: as the CD player scans the contents of a CD. The total number of tracks and playing time are then shown. ™Display: is shown if the CD R(W) is not finalised. 4. Press PLAY•PAUSE 2; (on the remote control 2;) to start playback. ™Display: Current track number and elapsed playing time of the track during CD playback. 5. To interrupt playback press PLAY•PAUSE 2;. Press PLAY•PAUSE 2; again to resume play. ™The display freezes and the elapsed playing time flashes when playback is paused. 6. To stop CD playback, press STOP 9. Note: CD play will also stop when: – the CD door is opened; – the CD has reached the end (unless you have selected REPEAT ALL); – you select another source: TAPE / TUNER. 1CASSETTERECORDER O PROG FM AM LW REPEAT AZ1565 CDRADIOCASSETTERECORDER OPENCL OSE STOP PLAY•PAUSE TUNER PRESET PROG SHUFFLE REPEAT SEARCH BAND SOUND CONTROL CENTER REMOTESENSOR FM AM BATLOW LW PROG SHUFFLE • • VOL 8 CD PLAYER Selecting a different track • Press SEARCH . or § on the set, (on the remote control . or ™) once or repeatedly until the desired track number appears in the display. • If you have selected a track number shortly after loading a CD or in the PAUSE position, you will need to press PLAY•PAUSE 2; (on the remote control 2;) to sta...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias