Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
SUPPLIED ACCESSORIES – 1X certified AC/DC 18V adaptor (Input: 100-240V ~ 50/60Hz 800mA, Output:18V 1.6A) – Docking kit •1 X Apple iPod dock (pre-installed with AJ301D); • dock adaptors (4 adaptors for different iPod types) – 1X AUX-IN cable CONTROLS (See 1) 1 POWER – switches the system on or to standby mode – stops active alarm for 24 hours – deactivates the sleep function 2 .1 / 2™ – adjust clock/alarm time – selects previous/next tracks in the dock mode – fast searches forward/backward in the dock mode 3 PRESET 1-5 – stores, recalls and shows radio station 4 SLEEP – activates the sleep function – deactivates the sleep function 5 DOCK – selects dock mode for Apple iPod 6 TUNER/ AUX – selects FM radio mode – selects AUX mode 7 2; – starts/pauses playback in the dock mode – selects 12 hour or 24 hour mode 8 VOL+/- – adjusts the sound level 9 MUTE – switches playback sound off and on. 0 Display – shows clock/alarm times and status of the set ! Dock connector (30 pins) – connects iPod player @ ALM 2 – activates/confirm ALARM 2 time setting – displays ALARM 2 time – switches off ALARM 2 time # REPEAT ALARM / BRIGHTNESS CONTROL – switches off the alarm for a 9 minute period – changes the brightness of the display illumination $ POWER jack – socket for AC/DC 18V adaptor % Pigtail – improves FM reception ^ ALM 1 – activates/confirm ALARM 1 time setting – displays ALARM 1 time – switches off ALARM 1 time & TIME SET – activates/confirm clock time/date setting * (Wake-up mode) DOCK•BUZZER •TUNER – selects alarm mode: dock, buzzer or radio ( AUX IN jack (3.5 mm) – connects to external audio source ) RESET – clears clock time setting POWER SUPPLY Mains adaptor 1 Connect the mains adaptor to the set's DC 18V socket and to the power socket. Helpful hints: To avoid damage to the set, use only the adaptor supplied! The type plate is located on the bottom of the set. Remote control Important! • Before using the remote control, remove the insulation plastic tab as shown in the figure. • If the remote control does not function correctly or the operating range is reduced, replace the battery with a new (CR2025) type battery. 1. Pull the battery tray out as shown in the figure below. 2. Replace a new battery according to polarity indication, and fully insert the battery tray back to the original position. 3 2 1 Batteries contain chemical substances, so they should be disposed of properly. CAUTION High voltage! Do not open.You run the risk of getting an electric shock. The machine does not contain any user-serviceable parts. Modification of the product could result in hazardous radiation of EMC or other unsafe operation. This product complies with the radio interference requirements of the European Community. SELF-POWERED BACK-UP The self-powered back-up conveniently allows your preset stations, alarm and clock time settings to be stored for up to 10 minutes when there is a power interruption e.g. AC power failure. The complete clock radio and backlight illumination will be switched off. • If power supply returns after 10 minutes and the display shows: clock time blinking - indicates you need to re-adjust the clock time. BASIC OPERATION Switching on the system •Press POWER. ™ The system will switch to the last selected source. •Press TUNER/AUX or DOCK. ™ The system will switch to the selected source. Switching the system to standby mode • In any source mode, press POWER. Switching off the volume temporarily Press MUTE on the remote control to stop sound play-back instantly. ™ Playback will continue without sound and the display shows MUTE . •To start sound playback you can: – press MUTE again; – adjust the volume controls; – change source. Illumination brightness Press REPEAT ALARM / BRIGHTNESS CONTROL once or more. • The brightness of the display can be adjusted: Bright . Low . Off . Bright . SETTING THE CLOCK AND DATE 1. In any mode, press and hold TIME SET until clock digits flashes. 2. Press 2; to select 12 Hours/ 24 Hours mode. 3. Hold down or press .1 / 2™ repeatedly to set and adjust the hours. 4. Press TIME SET to confirm. ™ The clock digits for the minutes flash. 5. Repeat the steps 3 - 4 until you complete all the other settings for minutes, year, month and days. TUNER 1 Press TUNER/AUX once to switch on the radio (FM only). ™ Display shows the radio frequency of the last selected waveband. Your preset station is also shown if you are listening to a preset. (See 2) 2 Adjust the sound using VOL+/-. 3 To select preset stations, press the respective PRESET button (1-5). TUNING TO RADIO STATIONS 1 Press and hold .1 / 2™ until the frequency in the display starts changing. ™Display shows “Scrh” during automatic tuning. ™After the system tunes to a station of sufficient reception, display shows its frequency. •To tune to a weak station, press .1 / 2™ briefly and repeatedly until an optimal reception is found. To improve reception (FM): Extend and position the pigtail fully to obtain optimum reception. STORING AND USING PRESE...