Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
• Insert the M4 bolt through the holder, front leg and into the lock nut. • Tighten the bolt with a Phillips screwdriver. Do not over-tighten. Holder Front Leg 5 8 Tapered End • Position the housing so that the hub is inward. • While pressing the button on the top of a front leg, insert it into the housing slot, as shown. Push the front leg until the button“snaps” into the hole in the housing. • Repeat this procedure to assemble the motor housing to the other front leg. • Pull the front legs down to be sure they are secure in the housings. If you can remove them, you have not assembled them correctly. Please re-read and repeat this assembly step. Press Buttons Front Legs Motor Housing Hole Housing Hub Slot 7 Clips Remote M4 Bolt - 1 Shown Actual Size • Place the rear base on a flat surface so that the buttons face the front base. • While pressing the buttons on each side of the rear base, fit the rear legs onto the rear base. Push the rear legs down until the buttons on the rear base “snap” into the holes in each rear leg. Front Rear Base Base Rear Legs Assembly • While standing on the rear base, pull the rear legs up. They should remain secured to the rear base. If you can remove the rear legs, you have not assembled them correctly to the rear base. Reread and repeat assembly step 10. • Set the frame assembly aside for Assembly step 21. • Position the seat face down, with the top of the seat facing you. • Position a seat tube so that the long end is upright and toward you and the curved end is toward the outside edge of the seat. • Insert the curved end of the seat tube through the holes in the ridges on the seat back. • Repeat this procedure to assemble the other seat tube to 6 the seat. Press Button Press Button Rear Legs Pull Up Pull Up Rear Base 10 11 12 Top of Seat Seat Tube Long Ends Ridges Curved End • Pull both rear legs out until they “snap” into place. Pull Rear Leg Pull Rear Leg 9 • Insert four M4 screws through the seat tubes, bracket and into the lock nuts. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. Assembly • Rotate the seat tubes down. • Fit the seat wire through the slot in the bracket as shown. 7 Seat Tubes 14 Bracket Bracket Slot Seat Wire Seat Tubes 15 16 • Position the bracket so that the tall end is toward the bottom edge of the seat. Hint: The M4 lock nuts have been assembled to the bracket at the factory.During shipment of this product, they may have fallen out.Check to be sure there is a lock nut in each hexagonal opening on the bracket. If one (or more) has fallen out, fit the lock nut into a hexagonal opening in the bracket.Make sure the rounded side of the lock nut is facing up. • Fit the grooves on the bracket to the seat tubes, as shown. Seat Tubes Bracket Grooves Tall End Bottom Edge of Seat 13 M4 Screw - 4 Shown Actual Size Lock Nut Hexagonal Opening Shown Actual Size M4 Lock Nut Rounded Side • While holding the seat wire in place, carefully turn the seat around so that the front of the seat faces you. • Position the seat wire cap so that the rounded edge is upright. • Fit each end of the seat wire through the hole in each seat wire cap. Ends of Seat Wire Assembly • Press to “snap” the seat wire caps into place. • Turn the seat face down. • Fit an accessory bin into the groove on each side of the seat, as shown. • Insert two #8 x 11/4" screws through each accessory bin and into the seat. Tighten the screws with a Phillips screwdriver. Do not over-tighten. 8 Seat Wire Cap Seat Wire Cap Grooves Seat Accessory Bin Accessory Bin Seat Wire Caps 18 19 20 • Lift the seat tubes slightly. • With the seat wire hanging down, insert the ends of the seat wire through the slots in the seat, as shown. Slots Seat Wire 17 #8 x 11/4” Screw - 4 Shown Actual Size Seat Wire Cap Hole Rounded Edge Up Seat Wire is Through Hole in Seat Wire Cap “Snap” in Place Assembly • Fit the pocket on the back of the pad onto the seat back. • Fit the waist belts through the smaller slots in the pad. 9 Waist Belts Pad Slot Slot 23 • Lift the bottom of the pad. • Insert the pad elastic loops through the holes in the seat bottom. • Insert the crotch belt through the slot in the pad. • From under the seat, fit the elastic loops onto the tabs on the seat bottom. 24 • Insert a #8 x 11/4" screw through each frame hub and into the swing tubes.Tighten the screws with a Phillips screwdriver. Do not over-tighten. • Again, push down on the seat to be sure the seat is secured to both frame hubs. Frame Hubs 22 Pad Elastic Loops Holes Crotch Belt • Position the seat assembly so that the front of the seat is toward the curved front base. • While pressing the buttons on the swing tubes, insert them into the frame hubs. Push the swing tubes up until the buttons “snap” into the hole in the frame hubs. • Push down on the seat to be sure the seat is secured in both frame hubs. Swing Tube Front of Seat Curved Front Base Push Button Frame Hub 21 Seat Bottom #8 x 11/4” Screw - 2 Shown Actual Size Assembly 10 ...
Este manual também é adequado para os modelos :Acessórios do bebê - B0323 (1.23 mb)