Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
N.B. Do not remove the lifter from the warmer. 9. Before feeding your baby: Always check feed temperature before feeding (a) Milk – shake the bottle or milk storage container and check the temperature of the milk by sprinkling a few drops on the back of your hand. (b) Food – stir the food thoroughly and test it yourself with a spoon to ensure it is not too hot. If food is not warm enough, consult the Troubleshooting Guide. N.B. Please ensure the lid of the container is tightly secured prior to shaking. 10. Unplug at the mains, and empty any residual water (viii). Ensure that the plug does not come into contact with water. If warming an additional bottle or container, continue from step 1. Otherwise, clean the inside and outside of the warmer with a damp cloth (viii).To remove the lifter for cleaning purposes ONLY, lift vertically up until it naturally resists. Push the handle away from you and rotate 90. or until it can naturally be removed, then lift out. N.B. For microbiological and hygienic reasons, once heated, milk and food should not be reheated again, and should be discarded if not used immediately. Please consult your health professional/breastfeeding adviser for further guidance about safety recommendations on feeding. N.B. If at any time the warmer is switched on and not running a cycle, it will automatically turn off after 3 minutes if no selections have been made. Approximate Warming Times Milk 115ml/4oz from room temperature 2 mins Milk 115ml/4oz from chilled 3 mins Milk 255ml/9oz from room temperature 3 mins Milk 255ml/9oz from chilled 4.5 mins Food 230ml/8oz from room temperature 5 mins Food 230ml/8oz from chilled 7 mins Care of your Digital Bottle and Baby Food Warmer Always unplug the warmer and allow it to cool before cleaning. Wipe the inside and outside of the warmer with a damp cloth. DO NOT USE AN ABRASIVE CLEANER. Using cool pre-boiled or filtered water in your warmer may reduce limescale build-up.When the warmer needs de-scaling, the mode and starting temperature symbols will flash on the electronic display.To ensure maximum effectiveness, you should de-scale your warmer every time it is required.To acknowledge the de-scale warning, press and hold the Power/Mode Selection or Volume Selection/Start Button for 3 seconds. If you do not wish to de-scale, please be aware that the unit will not remind you to de-scale on your next use, but will instead begin re-counting cycles until the next de-scaling is needed. IMPORTANT! DE-SCALING Under no circumstances should anything other than citric acid or vinegar be used as it may cause irreparable damage. Avoid contact with eyes as this may cause irritation. Keep out of the reach of children. EITHER: Mix one sachet of citric acid* (10g) with 200ml/7oz of water. Pour solution into the empty warmer. DO NOT place a bottle, jar or cup into the warmer when de-scaling. Close the lid of the warmer and programme the warmer to run with 310ml/11oz of milk from frozen. After the warming cycle has ended, leave the solution to cool for 30 minutes before emptying the warmer and rinsing with tap water.Wipe the inside and outside of the warmer with a damp cloth only. OR: Pour 100ml/3.5oz of vinegar mixed with 200ml/7oz of cold water into the warmer.Allow liquid to stand in the unit until any limescale has dissolved. DO NOT place a bottle, jar or cup into the warmer when de-scaling. DO NOT start the warming cycle. Empty the unit and rinse thoroughly.Wipe the inside and outside of the warmer with a damp cloth only. *Citric acid is available from most chemists and through Philips AVENT Customer Service. WARNING! The Digital Bottle and Baby Food Warmer is fitted with a non-rewirable moulded plug.The mains supply lead of the appliance CANNOT be replaced. If the lead is damaged, the appliance should be discarded.The supplied lead must not be used on any other appliance and no other cord should be used with the Digital Bottle and Baby Food Warmer. This product is manufactured to comply with the Radio Interference Requirements and the EEC Directive 89/336/EEC. Failure to follow instructions may cause scalding or damage to product. • Always ensure water has been added before switching on the warmer. • Always ensure that you are using the correct volume of water before beginning the warming cycle. The warmer should be emptied of residual water before each subsequent use. • Heating food jars or tins from frozen within this warmer is NOT RECOMMENDED. • To avoid possible scalding, do not place hands over the lid flap or open the lid flap during the warming cycle. • When warming a 330ml/11oz bottle, the lid flap will lift to accommodate the larger size. This will cause a small amount of steam to rise from the warmer. • To avoid possible scalding, take care when opening the lid after a completed cycle as there may be some residual steam. • When in use, the warmer contains hot water. Be careful to avoid spilling any water on yourself when removing contents from the warmer. • Us...