Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
4. Press (17). The power LED (19) will illuminate. 5. Press and hold (17) to switch off the baby unit. When the battery level is low, the power LED (19) will blink. Do not mix old batteries with new ones. Keep batteries away from small children Do not short-circuit & dispose of in fire. Remove the batteries if this device is not going to be used for a long period. Topcom Babytalker 2500 5 ENGLISH Topcom Babytalker 2500 4.2 Baby unit power supply 1. Connect the small plug of the AC adaptor to the power connector of the baby unit (29) and the other end of the adapter cable to the electric socket (230V/50Hz). Only use the enclosed adapter (6V DC / 300mA). 2. Press (17). The power LED will illuminate. 3. Press and hold (17) to switch off the baby unit. 4.3 Parent unit battery Installation 1. Turn the belt clip facing upwards. 2. Turn the screw 90° of the battery cover (14) on the backside of the baby unit in a counter clockwise direction using a screw driver. Remove the battery cover (15). Do not try to rotate the screw further than the position ‘open’. 3. Install the enclosed 2 ‘AAA’ rechargeable batteries following the polarity as shown. Do not install alkaline batteries! 4. Close the battery compartment. 5. Press (2). The LCD display (12) will illuminate. 6. Press and hold (2) to switch off the patent unit. 4.4 Parent unit power supply 1. Connect the power adapter cable to the main power socket (230V/50Hz). Only use the enclosed adapter (6V DC / 200mA). 2. Slide the parent Unit into the charger (6). The red charging light (7) illuminates. 3. It takes about 13 hours to charge the unit. 4. Press (2). The LCD display (12) will illuminate. 5. Press and hold (2) to switch off the patent unit. - + + - PTT Topcom Babytalker 2500 4.5 Link Do not place the baby unit or cables in the crib or within the arm reach of the baby (at least 1 meter away). When using the Babytalker the first time, it is adviced to test the connection. • Install the parent unit in the same room as the baby unit, but have at least 1 meter between the 2 units. • When both units are switched on, the parent unit will search for the baby unit. • The green link LED (9) on the parent unit will flash until they communicate. Once the link is established, the LED will light continuously. • The voice captured by the microphone will be audible on the parent unit. • The level of the detected speech is represented by the LED’s on top of the parent unit (1). • When the speech reached the maximum level, a beep will be audible. • When the connection is established, move the parent unit to the monitor room, but within the operation range. • When there is no connection, an alert signal (double beep) will be audible (out of range warning) and the green connection LED will blink. • Move the parent unit closer until the link is re-established. 4.6 Paging When your parent unit is lost, you can track it by pressing (18) on the baby unit for 2 seconds. The parent unit will emit a high beep tone for 30 seconds which helps you to find it very easily. • Press on the parent unit (2) briefly to stop the beep. 5 Using the Babytalker 2500 5.1 Volume adjustment 5.1.1 Parent unit There are 5 volume levels on the parent unit. • Press (11) to increase the volume level. • Press (10) to decrease the volume level. • When ‘OFF’ is displayed, the babies crying will only be visible by the LED’s on top of the unit. 5.1.2 Baby unit • Press (24) to increase the volume level. • Press (23) to decrease the volume level. The volume of the babyunit has effect on the talk to baby mode and when the melody is playing. Topcom Babytalker 2500 Topcom Babytalker 2500 5.2 Talk to baby With the Babytalker 2500 it is possible to talk to your baby. PTT • Press and hold (3) on the parent unit to talk to your baby. • Release the button to stop talking. Make your baby familiar with the talk function. If they do not know it, they might get confused. 5.3 Menu operation • Press (8) on the parent unit for entering the menu. • Press (11) or (10) to scroll through the menu. • Press (4) to select the desired setting. • Press (8) to leave the setting. 5.4 Display language • Press (8) on the parent unit, ‘Night Light’ is displayed. • Press (11) to select ‘Language’. • Press (4). The actual language is displayed. • Press (11) or (10) to select the desired language. • Press (4). • Press (8) to leave the menu. 5.5 Night Light 5.5.1 Remote activation: • Press (8) on the parent unit, ‘Night Light’ is displayed. • Press (4). ‘On?’ is displayed. • Press (4) again to activate the night light on the baby unit. • Press (8) to leave the menu. • To remotely deactivate the night light, follow the same instructions, but select ‘Off?’. 5.5.2 Local activation: Press (16) on the baby unit to switch the night light on or off. ENGLISH 7 Topcom Babytalker 2500 5.6 Lullaby 5 lullabies can be played on the baby unit. 5.6.1 Remote activation: • Press (8) on the parent unit, ‘Night Light’ is displayed. • Press (11) until ‘Lullaby’ is disp...