Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Tool needed for assembly: Phillips screwdriver (not included). • Requires one "D" (LR20) alkaline battery (not included) for operation. • Product features and decorations may vary from photo. Pad Right Base Wire Base Tube Left Base Wire 2 Feet Footrest Retainers Seat Back Tube Toy Bar 3 Toys (Toys may be different) Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. M7932pr-0726 ©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA 2 Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. Shown Actual Size M5 x 20 mm Screw – 4 This package contains small parts in its unassembled state. Adult assembly is required. IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad. Consumer Information Parts To prevent serious injury or death: • Fall Hazard -It is dangerous to use this product on an elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor. • Suffocation Hazard -Never use on a soft surface (bed, sofa, cushion) since the product can tip over and cause suffocation in soft surfaces. • Never leave child unattended. • Never use as a carrier or lift while child is seated. Never use the toy bar as a handle. • Always use the restraint system. • Never use as a car seat. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 Kg/20 lbs). WARNING CAUTION • Please read these instructions before assembly and use of this product. • Adult assembly is required. Tool needed for assembly: Phillips screwdriver (not included). • Requires one "D" (LR20) alkaline battery (not included) for operation. • Product features and decorations may vary from photo. Pad Right Base Wire Base Tube Left Base Wire 2 Feet Footrest Retainers Seat Back Tube Toy Bar 3 Toys (Toys may be different) Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. M7932pr-0726 ©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA 3 IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Left Base Wire • Place the base tube on a flat surface. • Position the left and right base wires as shown. • Fit the left base wire and right base wire into the base tube. Right Base Wire Base Tube 1 • Position the feet so the holes are toward you and the non-skid surface is down. • Fit the feet on the base tube, as shown. Feet Holes 2 • Insert an M5 x 20 mm screw through each foot and tighten. 3 • Position the footrest so that the soothing unit is upright. • Fit the footrest onto the ends of the base wires. 4 Footrest Base Wires Assembly 3 IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Left Base Wire • Place the base tube on a flat surface. • Position the left and right base wires as shown. • Fit the left base wire and right base wire into the base tube. Right Base Wire Base Tube 1 • Position the feet so the holes are toward you and the non-skid surface is down. • Fit the feet on the base tube, as shown. Feet Holes 2 • Insert an M5 x 20 mm screw through each foot and tighten. 3 • Position the footrest so that the soothing unit is upright. • Fit the footrest onto the ends of the base wires. 4 Footrest Base Wires Assembly 4 • Fit the seat back tube onto the ends of the base wire. • Push the seat back tube to be sure it is completely on the base wires. 5 Seat Back Tube • Fit a retainer to the outside of the seat back tube, as shown. Make sure the socket in the retainer is upright. • Insert an M5 x 20 mm screw through the hole in the seat back tube, base wire and into the inside of the retainer. • Repeat this procedure to assemble the other retainer to the other side of the seat back tube. • Pull the seat back tube up to be sure it is secure. If you can remove either end of the seat back tube, you have not assembled the retainers correctly. Remove the screws, re-read and repeat Assembly steps 5 and 6. 6 Retainer Socket Up • Position the pad above the frame. • Fit the upper pocket on the back of the pad onto the seat back tube. • Lift the footrest. Fit the lower pocket on the back of the pad onto the footrest. Lower the footrest. • Attach the pad fastener to the fastener on the soothing unit. 7 Footrest Soothing Unit Fastener Assembly 4 • Fit the seat back tube onto the ends of the base wire. • Push the seat back tube to be sure it is completely on the base wires. 5 Seat Back Tube • Fit a retainer to the outside...