Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Audiovox could void the user’s authority to operate the equipment. Headphone Jack Plugging in an optional headphone, the speaker is automatically silenced for private listening. When recording with the built-in microphone, you can use the optional headphone to listen to what is being recorded. Note that the headphone jack is designed to permit use of stereo headphones with your mono recorder. Playback will be heard in mono only. Play/Pause Button This convenient PAUSE feature is most helpful while recording because you can stop the recorder momentarily without resetting the control buttons. Slide the PLAY/PAUSE button to the PAUSE position to stop operation in PLAY, RECORD, FFWD, and REW modes. Slide button to the PLAY position to resume operation. Tape Speed • 2.4cm—is the tape speed which is compatible with most single-speed microcassette recorders. • 1.2cm—doubles the record time and will allow up to 2 hours of recording time when using both sides of a 60 minute (MC-60) microcassette tape. Tape Play To listen to your recorded microcassette, rewind to the starting point and press STOP/ EJECT button. Press PLAY and adjust the VOLUME to desired listening level. Rewind (REW)/ FAST FORWARD (FFWD) • REW—Slide switch to REW to rewind to beginning or any point of your recording. Press the STOP/EJECT button after you have rewound the desired amount. • FFWD—Slide switch to FFWD to advance the tape. Press STOP/EJECT button after you have reached the desired location on the tape. Review (REV)/ Cue This feature is helpful in finding the beginning or the end of the recorded segment on the tape. While in PLAY mode, Slide and hold the REV or CUE switch and listen for change from noise to silence (end of recording) or from silence to noise (beginning of recording). When desired portion has been reached, release the REV or CUE switch. Use the same procedure if you want to skip a portion or listen to the same segment again. TIP: Always push STOP/EJECT before storing. This will relieve pressure on certain parts in the recorder that might deform after long periods of time. Volume Control • Adjust the volume when in the PLAY mode to your preferred listening level. • Adjust the volume when in the RECORD mode to fine tune the sensitivity of the built-in microphone for record operations. Record Records continuously when the recorder is in the RECORD mode. 1. Press RECORD button (PLAY button will depress also). Note that your recorder is equipped with a microcassette sensing mechanism. This mechanism prevents the RECORD button from being pressed when cassette is not in the recorder. (See Erase Protection.) 2. Speak normally into the microphone. To obtain optimum recording quality, place the recorder with the microphone freely exposed to sound source and as close as convenient. A built-in automatic record level control will set record level for optimum recordings. Avoid recording near unwanted noise sources, such as air conditioners or fans. 3. Push STOP/EJECT button when finished recording. TIP: For conferences, to obtain optimum recording quality, place the recorder with the microphone freely exposed to the sound source and as close as convenient. A built-in automatic recording level control will set record level for optimum recordings. Avoid recording near unwanted noise sources, such as air conditioners or fans. Record with an External Microphone To record with external microphone, plug the microphone into the MIC JACK. The built-in microphone is disconnected. You can also use your own microphone for recording. Your microphone should be an Electret Condensor Microphone and it's impedance should be 2.2k ohm. Tape Speed Switch Using the Recorder IMPORTANT: Do not change speed while recording. Tape Erase To erase a tape simply record over the unwanted recording. Erase Protection When you record new material, the cassette deck records over whatever is on a tape. To protect a tape from accidental erasure, break off one or both plastic tabs (one for each tape side) on the side of the cassette tape. If you decide later to record on the tape, seal the hole with a piece of cellophane tape. QUIT SLACKING A little bit of slack in your tapes can cause scratches on the tape, or worse yet, the tape could break. If you notice some slack in the tape, use a pencil to tighten it up before you insert it. Cleaning the Tape Heads Over time, iron oxide particles from the magnetic tape build up on the parts that come in contact with the tape. These deposits can cause incomplete erasure, a muffled sound during playback. To clean the heads, open the compartment door, push the PLAY button and gently clean the heads, capstan and pinch wheel with a head cleaner. Allow 3...
Este manual também é adequado para os modelos :Ditado - RP3528 (470.16 kb)
Ditado - RP3528 (470.16 kb)