Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
• The REC indicator lights up. • You can also start recording immediately during playback. Press REC 0. 5. For brief interruptions, adjust PAUSE ;. To deactivate pause, slide the switch back again. 6. To stop recording, press 9 and the set is switched off. • The REC indicator goes out. • At the end of a tape, the 1 and REC ( keys are automatically released and the set switched off, unless PAUSE ; has been activated. 7. To check your recording, use the 5or 6keys (see CASSETTE PLAYBACK). GENERAL INFORMATION MAINTENANCE (see fig.4) • Clean the tape heads every month with a cotton bud dipped in alcohol, or by playing through a cleaning tape. • Use a soft damp cloth to wipe off dust and dirt. Don't use benzene or corrosives to clean the set. • Don't expose the set or cassettes to rain, moisture, sand or to excessive heat e.g. cars parked in direct sunlight. • Don't use C-120 tapes. TAKE CARE WHEN USING HEADPHONES Hearing Safety: Listen at a moderate volume. Use at high volume can impair your hearing! Traffic Safety: Do not use headphones while driving or cycling as you may cause an accident! ENVIRONMENTAL NOTE • The packaging has been minimized so that it is easy to separate into two materials:- cardboard and plastic. Please observe the local regulations regarding the disposal of these packaging materials. • Please inquire about local regulations on how to hand in your old set for recycling. RECORDING GENERAL INFORMATION English POWER SUPPLY CASSETTE PLAYBACK PyccIEE eaiAcaO eeeaEeoCAcaO aAeeOio POWER INDICATOR Whether the set is operated on batteries or a mains adapter, during playback or recording, the power indicator lights up. • The power indicator goes out when the set is switched off. • If battery power is low, the power indicator lights up only dimly and you will need to replace batteries. Batteries (not included) 1. Open battery door and insert two alkaline batteries, type R6, UM3 or AA as indicated inside the compartment. 2. Remove the batteries from the set if they are exhausted or not to be used for a long time. • Batteries contain chemical substances, so they should be disposed of properly. Mains Adapter (not included) 1. The voltage of the DC 3V adapter must match with the local voltage. The 3.5 mm adapter plug's 1.3 mm centre pin also must be set to the minus pole -. 2. Connect the mains adapter to the set's DC 3V ->+ socket and a wall socket. 3. Always disconnect the mains adapter if you are not using it. CASSETTE PLAYBACK 1. Open the cassette door and insert a tape (see fig. 2). 2. Press the door lightly to shut. 3. To start playback, press 1. 4. Adjust the sound with VOLUME. • For personal mono sound listening, insert 3.5mm headphones (preferably type 16 ohms) into the p socket. The built-in speaker will then be disconnected. 5. To fast wind, press 5or 6. Polski ZASILANIE ODTWARZANIE KASET CASSETTE PLAYBACK RECORDING 6. Watch the tape counter display to find the point in the tape you want to listen to. Press 9 to stop fast winding at the selected point. • 5or 6also allows you to fast cue or review during playback. Using the tape counter to monitor passages, hold down on 5or 6and release the key at the passage you want. Tape playback continues from this point. • To reset the tape counter display to 000, press the COUNTER RESET switch. 7. You can also adjust TAPE SPEED to find or listen to passages during playback. Set TAPE SPEED to: • . for high speed playback • 0 for normal speed playback • - for low speed playback. Remember to set TAPE SPEED to 0 for normal playback! GENERAL INFORMATION ON RECORDING • This set is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. You should only use NORMAL type cassettes (IEC type I) on which the tabs have not been broken. • Altering the VOLUME and TAPE SPEED controls will not affect the recording in progress with the exception of when VOICE ACT is in use and VOLUME is adjusted. • At the very beginning and end of the tape, no recording will take place during the 7 seconds when the leader tape passes the recorder heads. • Recording is permissible insofar as copyright or other rights of third parties are not infringed. PROTECTING TAPES FROM ACCIDENTAL ERASURE (SEE FIG. 3) To safeguard a particular cassette, simply break out the left tab. Recording on this side is no longer possible. If, however, you wish to record over this side or a tape with open tabs, cover the tabs with a piece of adhesive tape. VOICE ACT (ACTivation) VOICE ACT is a sound level sensor system which enables you to record only when the microphone receives sound at the preset level. The VOLUME wheel acts as the control for the microphone sensor. If sound stops or falls below the volume adjusted for the preset level, recording will pause hence preventing empty recording. To activate: 1. Push VOICE ACT to ON. 2. Turn VOLUME: Anti-clockwise – the sound level sensitivity drops and only sound near the microphone will be recorded. Clockwise – sound sensitivity is increased. D...