Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
how to operate and care for your beer dispenser. It also offers tips on how to get the best, as well as lowest cost, performance. ...... _^-;'", ,,_l=r_.rn_.rlt oarts use For parts or service information, call VVlI_:;': ,J,,,,,,_ .... ._ -_ the part number. Do not use the illustra-your nearest Sears store or Service tion number. Center, give the complete model number listed above. ice provided below the model number and serial number nce. They are located on the model number plate on the FULL ONE-YEAR W_ ON BEER DISPENSER For one year from the date of purchase, when this beer dispenser is operated and maintained according to owner's instructions attached to or furnished with the product, Sears will repair this beer dispenser, free of charge, if defective in material or workmanship. FULL FIVE-YEAR WARRANTY ON SEALED REFRIGERATION SYSTEM For five years from the date of purchase, when this beer dispenser is operated and maintained according to owner's instructions attached to or furnished with the product, Sears will repair the sealed system (consisting of refrigerant, connecting tubing and compressor motor), free of charge, if defective in material or workmanship. WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 698/731A, Sears Tower, Chicago, IL 60684 Part No. 302104 SEARS, ROEBUCK AND CO., U.S.A. Read and understand these instructions thoroughly before installing b. Push wingnut and beer tube of draft arm assembly beerdispenser. throughholeintopofcabinetuntildraftarmisrestingon cabinettop. ASSEMBLY 1. Carton Inventory Unpack and inspect the parts. Make sure all items are present and in good condition. 1 Draft arm assembly (Package includes 1 gasket for draft arm and 1 washer for connection to keg tapper) 1 CO2 regulator 1 CO2 cylinder 1 Keg tapper (Sankey type) 1 Cleaning kit 1 Pressure tube 2 Hose clamps 2 Keg supports (wooden plates) 1 CO2 cylinder retainer (spring) 1 Guard rail 1 Drip tray 4 Wheel casters 4 Hex head screws (5mm dia x 15mm long) 16 Machine screws (5mm dia x 12mm long) 8 Small screws (5mm dia x 10mm long) 2. Installcasters a. Empty the cabinet and then lay down the beer dispenser sidewayssothatthe doorhingesidecomesto the top. Be careful not to cause dents or scratches on the cabinet. Placing outer carton underneath the cabinet is recommended. b. Install casters to the four bottom corners of the cabinet with the four machine screws (5mm dia x 12mm long) for each caster. c. Stand the cabinet upright. 3. Install Draft Arm Assembly (See Fig. 1). a. Slide gasket over wingnut on bottomof draft arm assembly beer tube. Slide gasket up beer tube to draft arm base. Hex. Head Screw Draft Arm Assembly i I Gasket • / Small Screw Guard Rail .,_ / c. Alignholesindraftarmbasewithholesingasketandpilot holes in cabinet top, then secure draft arm to cabinet top withfour hex head screws (5mm dia x 15mm). 4. Install Guard Rail (See Fig. 1). a. Place guard rail on cabinet top and secure guard rail with eight small screws. INSTALLATION " 1. Installbeer dispenser on stronq,,lev_-IftnnLA_ia direct sunlight, heatZJb'0_sa_"a_moi-sture. 2. Connect to-120Vr-, out_et. Do not use extension cord. Use __q,,_X_tb three-prong grounded W'_ff'6"0t1"b, ,., .'t_"_ .. WARNING: Unless the _'d_O_"_gr-_nding method'Js'io/lowed, you are not _rotep_=d_,.agaim_-severe 'or lethal sh0_k in'_h+_'eventofa shortcircuitof an electrical cq.mponer=Lor_widng of beer dispenser. TEMPERATURE CONTROL 1. Controlislocatedonrear.Firstsetthe control at NORMAL position. Wait for 24 hours to check the temperature then adjust temperature control, if needed. DEFROST 1. Beer dispenser will not require much defrosting since the door opening is at a minimum. Defrost when V4inch frost is built up on the cold plate. The best time to defrost is when the keg is changed. To defrost, set temperature control at OFF position and leave door open until ice melts. Defrost water will accumulate at the bottom of interior cabinet which can be absorbed with a sponge or towel.Do notus6 heating devices or sharp objects to speed defrosting as this could damage cabinet liner of cold plate. Reset temperature control after defrosting is completed. INSTALLATION OF BEER SYSTEM 1. Installing CO 2 Cylinder and CO2 Regulator WARNING: CO2 GAS CAN BE DANGEROUS Read front pages of "Draught Beer Facts" book in cluded in your cleaning kit for safety precautions before installaing the CO2 cylinder. OPERATING INSTRUCTIONS FOR CO2 CYLINDERS Do notoperatevalvecontrolunlesscylinderiscompletely installedand connected. TURN HANDWHEEL FULLY COUNTERCLOCKWISE AS FAR AS IT WILL GO-. IMPORTANT: Ifvalveisnotfullyopenedthestemmaynot sealproperlyagainstthe upperpackingwasherandthe valve may leak. If leak occurswhen fully opened, tighten down packing nut under handwheel then open and close valve ...
Este manual também é adequado para os modelos :Dispensadores - 564.8815022 (386.35 kb)