Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
The standard model will produce up to 60 cups of water per hour at approximately 190°F (88°C). Due to high water temperature, for safety reasons, the tank is not under pressure. Consequently, there is a slight delay of water flow after the faucet has been activated. This is normal and indicates that the Faucet Compatibility 2 mounting bracket screws (and 2 plastic anchors if attaching to drywall) Materials required (not provided) Shut-Off valve with “T” fitting (EV312120) EVERPURE INSTANT HOT WATER DISPENSER(Connections must meet all local codes and ordinances.) from the faucet. expansion chamber is functioning properly. IMPORTANT INFORMATION 560H486P01 REV E CGHE1 Installation & Operating Guide Components tank mounting bracket tank When you purchase the Everpure® Commerical Grade Instant Hot Water tank, contents include: quick-connect fitting quick-connect fitting with filter and cap 1/4" (6.4 mm) O.D. copper tubing. Tools and Safety Equipment you may need (not provided) • ruler or measuring tape • pliers • hand or electric drill • small drill bit for starter holes • 13/8" drill bit - if no sink hole exists • safety glasses • bucket or pan • open-end wrench(es) • gloves • tubing cutter Only “Open Vent” faucets function with a instant hot water dispenser tank. Connecting a standard faucet will damage the tank and void the warranty. IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS VERY CAREFULLY When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions. 2. To protect against electrical shock, do not place cord, plugs, or appliance in water or other liquid. 3. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions. Return appliance to the factory for examination, repair or adjustment. See Warranty insert. 4. Do not use outdoors or in damp area. 5. Do not let cord hang over edge of table or counter, or touch hot surfaces. 6. Do not use appliance for other than intended household use. 7. When using this appliance, provide 4 to 6 inches of air space around the entire unit for air circulation. 8. Do not attempt to service this product. Repairs should be done by authorized service personnel. 9. Do not let children operate. The water can cause severe burns. SAVE THESE INSTRUCTIONS. THIS PRODUCT FOR HOUSEHOLD USE ONLY. The alert symbols displayed at right point to important safety information to make you aware of potential hazards that can cause serious injury or death. Please pay special attention to the information following these alerts and warnings. Failure to comply with these instructions can result in property damage, serious injury or death. WARNING DANGER ELECTRICAL REQUIREMENTS Recommended Ground Method For your personal safety, the hot water dispenser is equipped with a power supply cord having a 3-prong ground plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, ground-type outlet, grounded in accordance with the National Electrical Code, ANSI/NFPA 70 — latest edition* or CSA Standard C22.1, Canadian Electrical Code, Part 1, — latest edition** and all local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have a properly grounded, 3-prong outlet installed by a qualified electrician. WARNING Copies of the standards listed may be obtained from: * National Fire Protection Association **CSA International One Batterymarch Park 178 Rexdale Boulevard Quincy, MA 02269 Toronto, Ontario M9W1R3 If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. A 120 volt, 60 Hz, AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your hot water dispenser be provided. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire or electrical shock. NOTE: Use an outlet that cannot be turned on/off by a switch. HOT WATER CONCEPT Unlike a household water heater, this dispenser tank is not pressurized for safety reasons. For a conventional household water heater, the faucet valve is placed after the heater tank resulting in a pressurized tank. For a hot water dispenser, the faucet valve is placed before the tank, creating an “open vent” style faucet and consequently no pressure is built up inside the tank. OVERVIEW 1. Make sure you have all necessary parts, tools and materials as suggested on manual cover. 2. Determine a convenient location to mount your faucet. This can be an existing sink hole in the sink top (the spray hose opening for example) or you may drill another hole into the sink or counter-top. As you determine the location of your faucet, consider the container you will use with the ...