Assessments - 4, GPA: 5
(
)
)
|
Facilidade de uso
6. Secure, but do not overtighten both grille screws (Figure 14, 3). 7. Reconnect power to unit. Leveling It is important that units equipped with adjustable feet are level, for proper door and ice maker (if equipped) operation. To level units with adjustable feet: Figure 15 1. Use a level to check the levelness of the unit from front to back and from side to side. Level should be placed along top edge and side edge as shown (Figure 15). Figure 16 2. If the unit is not level, adjust the feet on the corners of the unit as necessary (Figure 16). 3. Check the levelness after each adjustment and repeat the previous steps until the unit is level. Door Alignment Check and Adjustment IMPORTANT Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps). Carefully examine the door’s gasket to assure that it is firmly in contact with the cabinet. Also make sure the door gasket is not pinched on the hinge side of the door. Figure 17 1. Loosen (do not remove) top (Figure 17) and bottom hinge screws. 2. Align door squarely with cabinet. 3. Make sure gasket is firmly in contact with cabinet all the way around the door (no gaps). 4. Tighten bottom hinge screws. 5. Tighten top hinge screws. 2 1 3 ULIN_0159_A ULIN_0183_A 1 1 ULIN_0042_A ULIN_0143_A 16 1115WC, 1175WC Door Reversal Black model doors may be left- or right-hand opening. Stainless steel units are not field reversible. Model 1115WC To reverse the door, perform the following: 1. Remove the grille and grille cap (two screws). Figure 18 2. Remove top hinge from cabinet (three screws) (Figure 18). Hold door to keep it from falling. 3. Lift the door off the bottom hinge. Figure 19 4. Remove bottom hinge from cabinet (two screws) (Figure 19). Figure 20 5. Remove screws on opposite side of cabinet (Figure 20). Note that there may be a nut behind one or both screws on either side. Figure 21 6. Install hinge on opposite side, bottom of cabinet (Figure 21). Replace nut on back side where installed. Align hinge outer edge with cabinet before tightening screws. Figure 22 ULIN_0143_A ULIN_0121 A ULIN_0122 A ULIN_0123 A 1 ULIN_0109_A 1115WC, 1175WC 17 7. Relocate plastic spacer/bushing (Figure 22) on bottom of door to opposite side, and place door on bottom hinge pin. Clean out bushing hole in door bottom with a screwdriver if necessary. Figure 23 8. Remove plastic hole plug (Figure 23) from door handle and relocate on opposite side. 9. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge. See Figure 26. Figure 24 10. Remove three plastic screw plugs (Figure 24) from hinge holes, top of cabinet, opposite side. Be careful not to scratch cabinet. 11. Place door on lower hinge pin. Invert and install upper hinge on door. Figure 25 12. Fasten upper hinge to unit (three screws) (Figure 25). Partially tighten screws. 13. Adjust door to assure proper seal. Tighten upper and lower hinge screws securely. 14. Replace three plastic plugs removed in Step 10 into holes on top of unit. Replace screws in holes in bottom of unit on opposite side. 15. Replace the grille and grille cap. Be sure to place grille cap on opposite side of unit from where it was originally. Model 1175WC To reverse the door, perform the following: 1. Remove the grille (two screws). Figure 26 2. Remove top hinge from cabinet (four screws) (Figure 26). Hold door to keep it from falling. 3. Lift the door off the bottom hinge. Figure 27 4. Remove four plastic plugs (Figure 27) in hinge holes, top of cabinet, opposite side. Be careful not to scratch cabinet. Plastic Plug Hole Plastic Plug Hole Hinge Screw Right Side Door Swing Right Side Hinge Invert Screw Invert Hinge Left Side Door Swing ULIN_0142_A ULIN_0144_A ULIN_0145_A ULIN ULIN_0105_A 18 1115WC, 1175WC Figure 28 5. Remove pivot screw from top hinge, invert screw and reinstall pivot screw in top hinge (Figure 28). Do not install hinge on cabinet at this time. Figure 29 6. Remove bottom hinge from cabinet (four screws) and screws on opposite side of cabinet (Figure 29). 7. Remove pivot screw from bottom hinge, invert screw and reinstall pivot screw in hinge (Figure 28). Figure 30 8. Install bottom hinge on cabinet, opposite side, aligning flat edge of hinge with outer edge of unit (Figure 30). Partially tighten screws. Figure 31 9. Relocate plastic spacer/bushing (Figure 31) on bottom of door to the opposite side. Clean out bushing hole in door bottom if necessary. Figure 32 10. Place door on lower hinge pin. Align flat edge of top hinge with outer edge of unit and fasten upper hinge to unit (four screws) (Figure 32). Partially tighten screws until door is aligned. 11. Adjust door to assure proper seal. Tighten upper and lower hinge screws securely. 12. Replace four plastic plugs removed in Step 4 into holes on top of unit. Replace screws in holes in bottom of unit on opposite side. 13. Replace the grille. Plastic Plug Hole Plastic Plug Hole Hinge Screw Right Side Door Swing ...
Este manual também é adequado para os modelos :Dispensadores - 1115WC (1.67 mb)