Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Replace splash panel. 14. Plug dispenser power cord into 20 amp rated NEMA 5-20 wall socket. 15. If dispenser is equipped with SensorSAFE remove protective plastic coating form dispense sensor labels. 16. Turn on power and bin signal rocker switches and test operation. 17. Clean and sanitize icemaker following instructions in icemaker manual. 18. Remove dispenser hopper access lid and clean and sanitize dispenser according to instructions on page 14. 19. Replace front cover and secure with screws. Installation is complete. Fig. 8 – Ice transport tube and ice level control stat mounting for units with top-mounted icemakers .75" ice level control stat 45° (19mm) Hand bend cap tube end to approximately 45° as shown 13 User information How the dispenser works Follett’s 110 series automatic load ice and water dispensers receive ice from Follett’s 400 lb (181kg)/day icemaker located in the dispenser base, in the cabinet top or in a remote location up to 20 ft (6m) away. Ice produced is stored in the bin section of the dispenser. When dispensing is activated, the wheel motor is energized, causing the wheel to turn. This moves ice to the dispense chute where it drops by gravity into the container held below the chute. In Follett’s continuous icemaking process, water freezes to the inside walls of the stainless steel evaporator. A rotating stainless steel auger carries the ice to the top of the evaporator where it is compressed and extruded through a nozzle on the outlet port. The ice is then pushed through a tube to the dispenser bin. When the storage area is full, a bin thermostat opens and shuts the icemaker off to avoid over-filling of the bin. The icemaker will restart after 20 minutes if the bin is calling for ice. How the SensorSAFE accessory works Follett’s SensorSAFE accessory maximizes sanitation and minimizes the possibility of cross-contamination by eliminating physical contact between the cup or container and dispenser. Sensors in the panel use reflected infrared light to detect the presence of the container and send a signal to a control board which then activates the appropriate components for ice or water dispensing. The SensorSAFE package includes a cleaning switch under the left side of the front cover which temporarily shuts off dispensing to allow cleaning of the panel and lenses. If the switch is not turned back on after cleaning, the dispenser automatically resets after two minutes for normal operation. SensorSAFE also includes a time limit safety feature which automatically stops ice dispensing after one minute of continuous dispensing. Dispensing can be resumed by moving the container away from the dispenser and returning it to the activation zone. How the chilled water accessory works Follett’s chilled water accessory uses ice from the dispenser’s storage hopper to chill incoming water supplied to the water station. The water chiller assembly is located in the dispenser cabinet under the storage hopper. As ice is dispensed, it is automatically fed into the water chiller assembly to chill the water coil inside the assembly. Cleaning and sanitizing procedures ! Always disconnect power before cleaning. Solution A: Prepare cleaning solution (200 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be 75.F – 125.F (24.C – 52.C). Solution B: Prepare sanitizing solution (50 ppm of available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be 75.F – 125.F (24.C – 52.C). Follett recommends the periodic cleaning schedule on page 15 to ensure the quality of ice provided. Use only recommended cleaning solutions. Do not use solvents, abrasive cleaners, metal scrapers or sharp objects. Recommended daily cleaning of drain pan 1. Remove all debris from drain pan. 2. Slowly pour 1 gallon (4L) hot water into drain pan to keep drain lines clear. 14 Recommended weekly cleaning 1. Wash drain pan and grille with Solution A above. Rinse thoroughly. 2. Slowly pour solution of one cup (8 oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain pan to help prevent algae growth in drain lines. If dispenser is a SensorSAFE unit: 3. Deactivate dispenser by depressing and releasing clean switch located on left side of unit under top front cover. 4. Clean lens using soft cloth and mild, non-abrasive cleaner. 5. Reactivate dispenser by depressing and releasing clean switch a second time (dispenser automatically reactivates after two minutes). Recommended semi-annual cleaning of dispenser hopper Note: If icemaker and dispenser are cleaned and sanitized at the same time, icemaker should be completed first. 1. Remove ice from dispenser. 2. Working inside storage area, remove center thumbscrew from dispense wheel, tilt wheel up toward back to clear baffle and lift wheel out. 3. Remove front cover, chute cover and clear plastic chute. 4. Wipe lid, wheel, baffle, inside of storage are...
Este manual também é adequado para os modelos :Dispensadores - 110CR400A/W (1.38 mb)
Dispensadores - 110CT400A/W (1.38 mb)