Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Note: Do not run condenser supply water through icemaker water filter system. 8. Connect condenser drain line to 19mm (3/4") FPT condenser outlet fitting on back of dispenser (Fig. 1E). Important: Do not connect condenser drain line to any other drain lines. 9. Install appropriate plug on provided cord and insert into wall socket. Refer to wiring diagrams (p.18, 19). 7 Fig. 1 – Rear connections, freestanding models 800mm 384mm 79mm79mm 259mm 267mm 171mm 20mm power cord 19mm (3/4") MPT icemaker drain location (B) (air-cooled only) access panel (31.5") (3.125") (3.125") (10.25") (15.125") (6.75") (10.5") (.8") (water-cooled only) (water-cooled only) (water-cooled only) (A) 10mm (3/8") push-in water inlet (19mm) 3/4" FPT drain (B) 10mm (3/8") FPT condenser inlet location (D) 10mm (3/8") FPT condenser outlet location (E) 19mm (3/4") MPT icemaker drain location (C) 10. Remove front cover of base section by removing two screws at bottom corners of cover. Allow cover to drop approximately 10mm (3/8") and pull forward. 11. Turn on water supply and check that water level in float reservoir (when full) is within 7mm (1/4") of mark on side of reservoir, and that float moves freely. Check for leaks. 12 Verify that water sensor tabs are immersed in water in reservoir. 13. Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull forward. 14. If dispenser is equipped with SensorSAFE, remove protective plastic coating from dispense sensor labels. 15. Turn on dispenser power and bin signal rocker switches. Check dispenser and icemaker operation. 16. Sanitize icemaker according to instructions in icemaker manual. Discard sanitized ice. 17. Turn off icemaker bin signal switch. 18. Remove dispenser hopper lid; clean and sanitize dispenser according to instructions beginning on page 16. 19. Turn icemaker bin signal switch on and replace front covers, securing with screws. 8 Installing countertop dispensers ! Dispensers with top mount icemakers cannot be mounted on legs.They must be bolted to counter. Use gloves when lifting icemaker to protect hands from sheet metal edges. 1. Position dispenser in desired location, mark Fig. 2 – Counter cut-out, all models dispenser outline on counter and remove dispenser. 2. Drill four 10mm (3/8") holes in counter 13mm (Fig. 2) to anchor dispenser to counter. (.5") Note: Follett countertop dispensers can have any or all utilities run directly through counter or out rear of dispenser. For 10mm dispensers with any utilities exiting through holes counter, make counter cut-out (Fig. 2) (.375") 3. If ice transport tube will exit out rear of dispenser, remove ice transport tube knockout (Fig. 5G) from rear of dispenser. Note: Utility connections can be accessed through front of dispenser by removing stainless steel splash panel, or by removing access panel (Figs. 4, 5) on back of dispenser. 4. If any electric utilities or water line will be connected through rear of dispenser, remove utility knock-out (Figs. 4, 5F) from rear of dispenser and install supplied protective grommet. 5. If power is to be supplied through counter cut-out, complete steps 6-9. If power is to be supplied through rear of dispenser, proceed to step 10. 534mm (21") 512mm (20.125") 318mm 420mm 166mm 10mm (.375") 39mm (1.5") 12mm (.44")267mm 229mm x 356mm (9" X 14") DRAIN PAN cut-out (10.5") (12.5") (16.5") (6.5") Fig. 3 – Top view, dispenser plumbing connections countertop drain pan (L) 19mm (3/4") FPT dispenser drain (K) alternate 19mm (3/4") dispenser drain location (G) 10mm (3/8") FPT water inlet (J) 10mm (3/8") FPT condenser water outlet (H) 10mm (3/8") FPT condenser water inlet 9 6. Temporarily remove rear access panel (Figs. 4 and 5) from rear of dispenser. 7. Loosen junction box mounting screws. Lift junction box and power cord up until cord and mounting screws clear notches on rear panel of dispenser. Remove Phillips head screws from right side of junction box. 8. Rotate junction box 90 degrees so that screw holes on right side of junction box align with holes on rear dispenser panel. Resecure junction box to dispenser using Phillips head screws. 9. Place power cord inside dispenser and replace access panel (Figs. 4, 5) to rear of dispenser. Note: For dispensers to be installed with utilities connected through rear of dispenser, it may be easier to make preliminary connections before dispenser is set in place. 10. Apply a thick bead, approx. 7mm (1/4") diameter, of NSF listed silicone sealant (Dow Corning RTV-732 or equivalent) 7mm (1/4") inside marked outline of dispenser. 11. Carefully position dispenser on counter. 12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter. (Water line to solenoid valve can be disconnected from water inlet valve by pushing in on release ring at end of inlet fitting while pulling on tubing.) 13. Secure dispenser to counter with four 10mm (3/8") bolts (supplied by others). 14. Smooth excess seala...
Este manual também é adequado para os modelos :Dispensadores - C/E25CR400A/W (1.38 mb)
Dispensadores - C/E25HR400A/W (1.38 mb)
Dispensadores - C/E25HT400A/W (1.38 mb)
Dispensadores - C/E50HR400A/W (1.38 mb)