Log:
Assessments - 4, GPA: 4.3 ( )

Instruções de Operação Turbo Air, Modelo TBD-2SB

Fabricante : Turbo Air
Arquivo Tamanho: 203.34 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


4 Turbo air CAUTION "IMPORTANT" On direct-draw dispensers the drain is located at the front of the cabinet. DIRECT DRAW To plumb in the drain, connect 5/8” P.V.C. pipe to the 5/8” barbed fitting supplies with the unit. * Don't pull out or Turn drain line. 5 Turbo air CAUTION "IMPORTANT" TBB-2SG, TBB-3SG, TBB-4SG A. Excessively opening the door will cause the breakdown. B. Handle with care as shutting the door. 1. POWER CORD -Be sure the power cord is connected to the proper voltage, and amps should be run before connecting power cord to outlet. -A protected circuit of the correct voltage and amperage must be run for connection of the line cord. -Unplug the unit, whenever performing maintenance functions or cleaning the refrigerated cabinet. -Compressor warranty is void if burnt out due to low voltage. 2. RE-STARTING -If unpluged, wait 5 minutes before re-starting. 6 Turbo air INSTALLATION 1. GOOD AIR CIRCULATION -Do not place any object that will restrict air flow in front or back grills. -Turbo air highly recommends that there is ample space in rear of unit. 3 inches or more is best. 2. PLACE ON STRONG GROUND -Be sure the location chosen has a floor strong enough to support the total weight of the cabinet and contents. 3. DO NOT PLACE NEAR HEAT -Be sure to avoid hot corners and locations near stoves. -High ambient temperature will make cooling efficiency lower. 4. INDOOR USAGE ONLY -Be sure to install this unit indoor, so it will not get wet from the rain. 5. STABILIZING -Make sure the unit is installed in a stable condition. 6. LEVELING -Be sure that the unit is level from front to back and side to side. 7. Do not plug in with other units on same breaker. 8. Do not run on extension cord. 7 Turbo air CLEANING Before cleaning, unplug the unit. 1. CLEANING THE INTERIOR AND EXTERIOR -The interior and exterior of the unit can be cleaned using warm water with soap. -Do not use an abrasive cleaner because it will scratch the surface. 2. CLEANING THE CONDENSER FINS -To maintain proper refrigeration performance, the Condenser coil must be free of dust, dirt, and grease. This will require periodic cleaning. Condenser fins should be cleaned at least every three months (90 days) or as needed. -To clean condenser, unplug the unit. Condenser can be cleaned with vacuum, brush, or CO2 (high pressure air). 3. CLEAN THE GASKET -The door gasket should be cleaned frequently to maintain proper sealing. 4. CLEAN THE DRAIN PAN -Empty the Drain Pan which is located under the unit, periodically. -When reinstalling Drain Pan, make sure Drain Hose is placed back in pan. 5. CHECK AFTER CLEANING -Plug unit back in. -Check that the unit is operating properly. 8 Turbo air BASIC OPERATION REFRIGERATORS 1. The controller(thermostat) is located at the back right inside of the unit. 2. The factory setting maintains about 38°F(3°C) inside. 3. Set toward “counter clock wise” warmer temperature and “clock wise” for colder temperature. Temperature Controller (Thermostat) 4. The ther...

Este manual também é adequado para os modelos :
Dispensadores - TBB-1SB (203.34 kb)
Dispensadores - TBB-1SB (203.34 kb)
Dispensadores - TBD-1SB (203.34 kb)
Dispensadores - TBD-1SD (203.34 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias