Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
CAUTION: BURN HAZARD Exposed surfaces of dispenser and any container may be HOT to the touch, and can cause serious burns. CAUTION: BURN HAZARD DO NOT fill water bottle with hot water. Splashing hot water can cause burns. OPERATION (continued) 9 INITIAL SET-UP: PORTABLE DISPENSERS 1. Turn POWER switch OFF. Turn WATERLINE / PORTABLE switch to PORTABLE Turn HEATER switch OFF. Turn COLD/HOT / HOT/HOT switch to HOT/HOT Turn DISPENSE / FLUSH switch to flush 2. Add water to tank. NOTE: To avoid an overflow when the water bottle is installed, fill only until water touches the LOW WATER probe. 3. Fill water bottle (SUPPLIED BY OTHERS). Invert water bottle and insert in tank. 4. Connect unit to electrical power. Turn POWER switch ON. Turn the HEATER switch ON. Place tank cover on water tank. 5. Place an empty container under the left dispensing nozzle. Press and hold left dispense key for several seconds. Discard all water generated. Repeat for center (9456 only) and right dispense nozzles. 6. Turn DISPENSE / FLUSH switch to DISPENSE. 7. Fill and install the PRODUCT HOPPERS (see page 10). 8. Close front door. Install the drip tray assembly. When water reaches serving temperature, dispenser is ready to use. IMPORTANT: The heating element will be damaged if it is energized without sufficient water. The element must be covered with water at all times it is in operation. When the REFILL TANK WHEN ON light glows, the bottle is empty. The tank is approximately half-full. Refill the water bottle promptly to avoid damaging the heating element. CAUTION: BURN HAZARD Exposed surfaces of dispenser and any container may be HOT to the touch, and can cause serious burns. CAUTION: BURN HAZARD DO NOT fill water bottle with hot water. Splashing hot water can cause burns. OPERATION (continued) NOTE: Hoppers and motors for various products are essentially identical. In a cold / hot dispensing mode, the cold product must be placed in the left dispenser only. Otherwise, product may be placed in and dispensed from either hopper. SUGGESTION: For easy identification of the hopper contents, a 2” strip of “frosty” tape placed on the front of the hopper is a handy place to write the contents name. NOTE: Keep front door closed when operating dispenser. This prevents excessive steam and humidity from entering the hopper compartment. FILL PRODUCT HOPPERS 1. Hoppers and covers should be thoroughly washed and dried. Examine hoppers for completeness and proper assembly prior to placing them into service. 2. Fill the hopper with the desired product powder and install the hopper cover. 3. Apply the appropriate label to the door assembly, above the touch pad keys, from the provided sheet of labels. Additional labels are available from your Authorized Bloomfield Distributor. INSTALL PRODUCT HOPPERS 1. Manually position the U-Shaped clevis HORIZONTALLY so that it will engage with the drive motor drive pin when it is installed in the hopper compartment. See illustration below. 2. Press the appropriate selection key to position the motor drive pin VERTICALLY so that it will engage with the hopper clevis without interfering with the hopper sliding to its full rear position. 3. Insert the hopper mounting tray by setting it over the mounting lugs, then pulling it as far forward as it will go. The tray should lay flat against the bottom of the dispenser inner cavity. 4. Slide the hopper against the side rail of the mounting plate. Slightly lift up the front of the hopper while pushing it back until the back edge of the hopper slips under the mounting lug on the rear floor of the inner compartment. 5. Place cup under blender spout, dispense and discard a serving from each hopper to prime the system. 10 NOTE: In the illustration, the clevis and drive pin are shown rotated and engaged. To install the hopper, the clevis should be horizontal, and the drive pin vertical. CLEANING INSTRUCTIONS CLEANING INSTRUCTIONS PROCEDURE: Daily Cleaning - Dispenser PRECAUTIONS: Avoid splashing hot water from tank FREQUENCY: Daily TOOLS: Mild Detergent, Clean Soft Cloth or Sponge 1. Open front door. Turn the DISPENSE / FLUSH switch to the FLUSH position 2. Place a large cup under the right dispensing spout. Press and hold the left dispense button, for approximately 10 seconds. 3. Repeat Setp 2 for the center (9456 only) and right dispensing systems. 4. Return the DISPENSE / FLUSH selector to the DISPENSE position. Discard all water generated. 5. Wipe the outer surfaces of the dispenser with a clean cloth dampened with warm water and mild detergent. Rinse by wiping with a clean cloth dampened with warm water. 6. Remove, empty and reinstall drain pan. Procedure is complete CAUTION: BURN HAZARD Hot water in the tank can cause severe burns. Allow machine to cool before moving or servicing. DO NOT tip or move machine when water in tank is hot. CAUTION: SHOCK HAZARD Do not submerge dispenser in water. Do not pour or splash water into cabinet, keypad or front door. IMPORTANT: DO NOT use ...
Este manual também é adequado para os modelos :Dispensadores - 9454 (1.51 mb)