Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
NOTE: On subsequent fill-ups, unit should take less than 30 minutes to chill. 3. Press and hold each button to ensure all air has been purged from the unit so water flow is steady. REPLACING WATER FILTER Replacement filters may be purchased at most retail outlets or To replace your filter, follow “Water Filter Setup” on page 4. TIPS AND HINTS • Drinking 4 to 8 glasses of water each day is healthy! Your countertop chiller makes it easy. • Regular use of cleaner, filtered water in your automatic coffeemaker means less frequent decalcification treatments. • Use filtered water in your iron to reduce mineral build-up. • Treat your pets to cleaner, filtered water. • Cleaner, filtered water makes tea and instant soup or coffee taste better. • Keeping the upper tank full helps increase the filtering process as well as the flow rate of water from spigots. • Proper setup of the filter (as instructed on page 4) will maximize the reduction of contaminants and optimize taste of water. • Conserve energy by unplugging your unit when only room temperature filtered water is needed. • You may notice some condensation and water droplets on the lid and tanks of your unit. This is normal due to the cooling system. CLEANING AND CARE CAUTION: To prevent personal injury or electric shock, always unplug your Cuisinart® ® Countertop Filtration System from outlet before cleaning. Do not immerse base in water or other liquid. 1. Unplug the unit from outlet. 2. Remove the filter and place it in a bowl. 3. Lift upper water tank and let it drain into lower tank, and set it aside. Then lift lower tank off base and empty. Careful, a full tank can be very heavy! 4. Clean the water tanks and the cover with warm soapy water. NOTE: Remove filter timer before washing lid. Filter timer is not immersible. 5. The base is not immersible. Simply wipe it clean with a damp cloth. 6. Dry thoroughly when clean. TROUBLESHOOTING Symptom Possible Cause Solution It takes longer than 45 minutes for the water to pass through the filter. Some air is still in the filter. Place filter in an empty bowl, then fill with water, making sure it is fully submerged. Resoak it for 10–15 minutes, or until no more bubbles are observed. Unit does not dispense water when buttons are pushed. Internal water tank is not completely filled with water. Review “Filling the Internal Tank” on page 5 to be sure it was done correctly. Make sure the lower water tank is full. Continue to press and hold push buttons until water flow is steady. If unit still won’t dispense water or flow does not become steady, contact Customer Service. Water continues flowing from spigot after push button is released. Push button is stuck. Remove water tanks from the base. Continue pressing button until it no longer sticks. COLD water LED does not light up. 1. Unit might not be plugged into outlet 2. There is no water in tanks. 1. Make sure unit is plugged into outlet and is not controlled by a wall switch. 2. Make sure air has been purged from internal tank, as stated on page 5. 3. If there is water in the tank, it will take about 80 minutes for the water to chill the first time. It takes only about 30 minutes for subsequent fill-ups. Filter Timer does not show “Filtering” or “Replace.” Battery is dead. Contact Customer Service for replacement filter timer. Leakage on the countertop. 1. Water tanks are not properly seated on base. 2. Drainage plug is not fully engaged. 1. Make sure water tanks are seated properly on the base. 2. Ensure that drainage plug is correctly installed on the bottom of the base. Water leaks from the top cover. Water tanks are overfilled. Drain excess water from tanks by pressing push buttons. ROOM temperature water is warm. ROOM temperature water must be used on a regular basis. STORING THE UNIT Bottom of unit 1. Unplug the unit from outlet. 2. Remove empty water tanks, filter and cover. 3. Bring base to sink. 4. Drain internal reservoir by tilting unit slightly and removing the plastic drainage plug from bottom of unit. Plug is tightly inserted and must be gently, but firmly, worked to remove. 5. When water has completely drained, replace plug, tanks, filter and cover. Drainage Plug 6. Your Cuisinart Countertop Filtration System is ready to store. TECHNICAL SPECIFICATIONS Unit: WCH-1000 1 Cuisinart® ® Countertop Filtration System 1 Cuisinart® Water Filter System Capacity up to 3 months/ 48 gallons/ 181 liters Maximum Input Temperature 104°F (40°C) Minimum Input Temperature 34°F (1°C) Maximum Output Temperature 104°F (40°C) Minimum Output Temperature 44°F (7°C) Rated Service Flow 6 gallons / 22.7 liters per day (may vary according to water conditions) Electrical Requirements AC~120V 60Hz 1A 75W System Tested and Certified by WQA against NSF/ANSI Standard 53 for the reduction of Lead, Benzene, Cadmium, Copper, Mercury, Tetrachloroethylene, Toluene, and Standard 42 for the reduction of Chlorine Taste and Odor. See Performance Data Sheet for specific test condition...
Este manual também é adequado para os modelos :Dispensadores - WCH-1000 (2.03 mb)