Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
? Remove cap. ? Carefully lift bottle (approx. 40 lbs.) using your legs and not your back. Do not place hands on opening of bottle while placing in reservoir. ? Insert the water bottle on the water intake over reservoir opening so it settles properly on it. ? Wipe off any water which may have splashed on dispenser top. When a new bottle is installed you must open the hot water faucet and remove no less than 4 full cups of water to insure the water flows properly and the water reservoir is at the proper level. • Cold Water Control Turn the cooling switch (13) on. The green indicator (4) will be lit and the process begins. When the water reaches the right temperature the green light goes off automatically. • Hot Water Control Turn heating switch (12) on, the red indicator (2) will be lit and the unit will begin to heat the water. When When the water reaches the right temperature the red light goes off automatically. When the temperature goes down to approx. 80. C (176. F), the red indicator will glow again and another heating process starts. NOTE: THE HOT WATER FAUCET HAS A CHILD-SAFETY GUARD ATTACHMENT. To get hot water: ? Slide safety button on faucet up. ? Continue holding safety button while pushing in faucet as long as water is being dispensed. ? When faucet is released, make sure to return it to the original position. • Cup Dispenser (Optional) A cup dispenser may be installed by using the mounting holes (covered with plastic caps) located near the top of the right side panel of the cooler. The cup dispenser comes equipped with a mounting bracket and screws and may be ordered by completing the enclosed order form provided with your instruction manual. CARE AND MAINTENANCE ? ? ? Wash the inside of the reservoir with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. The drip tray and water faucets should be cleaned with mild detergent and warm water. At regular intervals or once a month inspect the coils located across the back of the dispenser. Vacuum accumulation of dust or clean it with a hard brush. TAKING DISPENSER OUT OF SERVICE ? If the water dispenser will not be used for a long period of time, unplug the power cord from the wall outlet. ? Drain the water through the faucets. ? Turn the switch marked “HOT” to the “OFF” position. ? Drain the water from the tanks by removing the plug from the back of the dispenser. WARNING—THE WATER COMING OUT OF THE BACK SIDE MARKED “HOT” MAY BE SCOLDING. • Unit should not be transported on the sides. Place it upright if possible and cover it with a blanket. Installation instructions on how to secure your Avanti unit to the wall 1Attach the mounting brackets provided, into the pre-drilled holes located at the back of the unit side panels (see picture 2A) by using the self-tap screws provided. 2After both brackets are properly installed, use the other end of the bracket to assist in aligning the holes to be drilled on the wall as follows: Measure the center of the bracket mounting hole and the ground (see picture 2A), and measure the distance between the center of both brackets mounting holes (see picture 2B). Both of the above measurements will give you the exact location for drilling the holes on the wall where the unit will be secured. 3Please be aware that when securing these brackets to the wall, different types of bolts may be used, depending on the different types of wall construction (these bolts are not included). If you are not able to obtain the measurements as explained above, you can also mount and secure both brackets to the unit. Move the unit to your desired location and mark the wall using the holes at the other end of the bracket. PROBLEMS WITH YOUR WATER DISPENSER? You can solve many common water dispenser problems easily, saving you the cost of a possible service call. Try the suggestions outlined below to see if you can solve the problem before calling the servicer. TROUBLESHOOTING GUIDE PROBLEM Water dispenser does not operate. POSSIBLE CAUSE Not plugged in. The circuit breaker tripped or a blown fuse. Water cooler is not cold enough. Check to be sure the cold switch on the back is ON. The water dispenser does not have the correct clearances. Water dispenser hot water is not hot enough. Check to be sure the hot switch on the back is ON. Compressor turns on and off frequently. The room temperature is hotter than normal. The temperature control is not set correctly. The water dispenser does not have the correct clearances. Vibrations. Check to assure that the water dispenser is level. The water dispenser seems to make too much noise. The rattling noise may come from the flow of the refrigerant, which is normal. As each cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your water dispenser. Contraction and expansion of the inside walls may cause popping and crackling noises. The water dispenser is not level. SERVICE FOR YOUR WATER DISPENSER We are proud...