Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Cleaning the Inside IMPORTANT: Unplug the wine chiller before cleaning. To clean the inner liner and racks, use a warm water and baking soda solution— about one tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry. Do not use detergents, scouring powders, spray cleaners or other harsh chemicals to clean the interior. The vinyl door gasket may be cleaned with mild soap and water or a baking soda solution. Rinse well. Defrosting Defrost whenever frost on the inside surfaces of the storage area becomes 1/8 . (3 mm) thick. Never use a heater of any kind, scraper or sharp instrument to remove frost as it may damage the wine chiller. To defrost, unplug the wine chiller. Remove the contents and wipe inside surfaces and racks with a clean towel. If frost does not come off easily, allow the frost to melt somewhat and wipe off. After defrosting, make sure inside surfaces are dry; then return the contents to the wine chiller and set the temperature control to the desired setting. Consumer Instructions InstallationInstructions Care and 7 Consumer Support Troubleshooting Tips Care and Cleaning OperatingInstructions InstallationInstructionsSafety Instructions Care and cleaning. In the Event of a Power Failure If the power fails, open the door as infrequently as possible to maintain the temperature. A gradual rise in temperature should not have any adverse effect on the wine. If it is extremely hot, you may want to unload the wine from the wine chiller and move the wine to a cooler location until power is restored. When power is restored, the controls automatically are set to the RED WINE setting. If needed, reset the controls to the desired setting. Preparing to Move Unload the wine, then secure the racks by Be sure the wine chiller stays in an upright taping them in place to prevent damage. position during the move. Replacing the light bulb. Housing Bulb Step 5: Remove two screws Unplug the wine chiller. If the door is locked, unlock it. The light bulb is located behind a light shield in the ceiling of the wine chiller near the front. To remove the light shield, remove the two screws at the back corners of the shield. Pull down on the back of the light shield to release the two front tabs. Remove the light bulb housing by removing the two screws that attach the housing to the ceiling of the wine chiller. Pull the bulb out of the receptacle. Replace with a 5 watt, 12 volt bulb. This type of bulb is available at most automotive parts stores. WARNING: Using a bulb rated higher than 5 watts may damage the electronic controls on the wine chiller. Attach the light bulb housing to the ceiling of the wine chiller with the two screws. Make sure not to pinch or damage any of the wires attached to the housing. Line up the light shield with the indentation on the ceiling of the wine chiller, then push the front of the shield up until the front tabs clip into place. Replace the screws at the back of the shield. Plug the wine chiller back in. 8 Reversing the Door. Top cover Remove screws Back of wine chiller Unplug the wine chiller. Remove the two screws at the back of the top cover. Lift the back of the cover up about 2. (5 cm) and then slide it forward slightly, but do not remove. Top cover Disconnect power connectors Remove screws and top hinge, and move to other side Remove screws and move to other side Remove plug button and move to other side Front of wine chiller Top of wine chiller Tilt the top cover on its side. Locate the power connectors at the front of the cover. Disconnect each connector by pressing in on the locking tab on the side of the connector, then pulling out. Set cover aside. Carefully lay the wine chiller on its back. Remove the screws on the top hinge (right side). Remove the hinge. On the opposite side, remove the screws attaching the top plate to the cabinet, and install them in the holes left vacant by the top hinge screws. Remove the small plug button from the top left side of the door and install it in the hole on the right side. Insert the hinge pin from the top hinge into the hole on the top left side of the door. Attach the top hinge to the cabinet with the screws. Make sure the door is aligned with the wine chiller cabinet before tightening the screws. Safety Instructions InstallationInstructions OperatingInstructionsCare and Troubleshooting 9 Consumer Support Troubleshooting Tips Care and Cleaning OperatingInstructions InstallationInstructionsSafety Instructions Reversing the Door. Remove leveling leg, screws, bottom hinge and washer, and move to other side Remove leveling leg and spacer and move to other side Bottom of wine chiller Remove right door stop and screws. Install left door stop (packed separately) and screws on other side Remove the bottom hinge by removing the screws and leveling leg. Remove the right door stop and install the left door stop (WR13X10274), packed separately, on the opposite side. Re...